No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Configuration Guide - Basic Configuration

S7700 and S9700 V200R011C10

This document describes methods to use command line interface and to log in to the device, file operations, and system startup configurations.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Basic Configuration on the Device at First Login

Basic Configuration on the Device at First Login


This section describes how to configure the time and date, device name, management IP address, and the user level and authentication mode for Telnet users at first login .


  1. Set the time and date on the device.
    1. Run system-view

      The system view is displayed.

    2. Run clock timezone time-zone-name { add | minus } offset

      The time zone is set.

      By default, the system uses the Coordinated Universal Time (UTC) time zone.

      • add: adds the specified time zone offset to the Coordinated Universal Time (UTC). That is, the sum of the default UTC time zone and offset equals the time zone specified by time-zone-name.

      • minus: subtracts the specified time zone offset from the UTC. That is, the remainder obtained by subtracting offset from the default UTC time zone equals the time zone specified by time-zone-name.

    3. Run quit

      Quit the system view.

    4. Run clock datetime HH:MM:SS YYYY-MM-DD

      The current time and date are set.

      If the time zone is not set, the time set using this command is considered as the UTC time. Before setting the current time, you are advised to confirm the current time zone and set the correct time zone offset.

    5. Run system-view

      The system view is displayed.

    6. Run clock daylight-saving-time time-zone-name one-year start-time start-date end-time end-date offset or clock daylight-saving-time time-zone-name repeating start-time { { first | second | third | fourth | last } weekday month | start-date1 } end-time { { first | second | third | fourth | last } weekday month | end-date1 } offset [ start-year [ end-year ] ]

      Daylight saving time (DST) is set.

      By default, DST is not configured.

      If you configure periodic DST, the combination of the DST start time and end time can be any of the following: date+date, day of the week+day of the week, date+day of the week, and day of the week+date. For the configuration method, see clock daylight-saving-time.

      When DST is used, you can run the clock timezone time-zone-name { add | minus } offset command to set the time zone. The time zone in the output of the display clock command is, however, the name of the DST time zone. When DST ends, the system displays the original time zone.

  2. Set the device name and management IP address.
    1. Run sysname host-name

      The device name is set.

      By default, the device name is HUAWEI.

      When the network management tool needs to obtain the network element (NE) name of a device, you can run the sys-netid command to set an NE name for the device.

    2. Run interface interface-type interface-number

      The interface view is displayed.

      In addition to the management interface on the device, you can also assign the management IP address to a Layer 3 interface such as a VLANIF interface on the device.

    3. Run ip address ip-address { mask | mask-length }

      The management IP address is assigned.

      The management IP address is used to maintain and manage the device. Configure the IP address and routes based on the network plan to ensure that the routes between the terminal and device are reachable.

    4. Run quit

      Return to the system view.

  3. Set the user level and authentication mode for Telnet users.
    1. Run telnet [ ipv6 ] server enable

      The Telnet server is enabled.

      By default, the Telnet server is disabled.

    2. Run user-interface vty first-ui-number [ last-ui-number ]

      The VTY user interface view is displayed.

    3. Run protocol inbound { all | telnet }

      The VTY user interface is configured to support the Telnet protocol.

      By default, a VTY user interface supports the SSH protocol.

    4. Run user privilege level level

      The Telnet user level is set.

      By default, users who log in through the VTY user interface can access commands at level 0.

    5. Run authentication-mode aaa

      The authentication mode for Telnet users is set to AAA authentication.

      By default, no authentication mode is configured for the VTY user interface. An authentication mode must be configured for the VTY user interface; otherwise, users cannot log in to the device.

      The system provides three authentication modes: AAA authentication, password authentication, and non-authentication. AAA authentication requires both the user name and password, and is therefore more secure than password authentication. Non-authentication mode is not recommended because it cannot ensure system security. This section describes how to configure AAA authentication. For details on configuring other authentication modes, see Configuring an Authentication Mode for a VTY User Interface.

    6. Run aaa

      The AAA view is displayed.

    7. Run local-user user-name password irreversible-cipher password

      The user name and password for Telnet-based login are configured.

      The value of password can be a plain-text string of 8 to 128 characters or a cipher-text string of 68 characters.

      A simple password may cause a potential security risk. To enhance security, a plain-text password must contain at least two of the following: uppercase letters, lowercase letters, digits, and special characters excluding spaces and question marks (?). In addition, the password cannot be the same as the user name or the mirror user name.

    8. Run local-user user-name service-type telnet

      The login mode is set to Telnet.

  4. Save the configuration.

    After basic configuration is complete, you are advised to save the configuration. If the configuration is lost, the connection and configuration for the first login must be performed again.

    1. Run return

      Return to the user view.

    2. Run save

      The configuration is saved.

      The current configuration has been saved in the configuration file. For details, see Saving the Configuration File.

Verifying the Configuration

  • Run the display clock command to check the current date and clock setting.
  • Run the display ip interface brief [ interface-type [ interface-number ] ] command to check brief information about the IP address on the interface.
  • Run the display user-interface [ ui-type ui-number1 | ui-number ] [ summary ] command to check the physical attributes and configuration of the user interface.
  • Run the display local-user command to check the local user list.
Updated: 2020-02-04

Document ID: EDOC1000178308

Views: 101325

Downloads: 152

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next