No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

S7700 and S9700 V200R011C10

This document describes the configuration of Ethernet services, including configuring link aggregation, VLANs, Voice VLAN, VLAN mapping, QinQ, GVRP, MAC table, STP/RSTP/MSTP, SEP, and so on.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for VLAN Termination

Licensing Requirements and Limitations for VLAN Termination

Involved Network Elements

Other network elements are not required.

Licensing Requirements

VLAN termination, that is, QinQ and Dot1q on a sub-interface, is often used on an MPLS network, so the device must be enabled with MPLS. MPLS requires a license. By default, MPLS of a newly purchased device is disabled. To use MPLS, apply for and purchase the license from the equipment supplier. VLAN termination itself can be used without a license.

Software Requirements

Table 8-2  Products and versions supporting VLAN termination

Product

Product Model

Software Version

S7700

S7703, S7706, S7712

V100R003C01, V100R006C00, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005C00, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C10

S9700

S9703, S9706, S9712

V200R001(C00&C01), V200R002C00, V200R003C00, V200R005C00, V200R006C00, V200R007(C00&C10), V200R008C00, V200R009C00, V200R010C00, V200R011C10

NOTE:
To know details about software mappings, see Hardware Query Tool.

Feature Limitations

  • Only E series cards, X series cards, SC cards among S series of the S7700&S9700 support the termination sub-interface. Starting from V200R007C00, X1E cards among X series support termination sub-interfaces. For details, see the card classification in Hardware Description.

  • Termination sub-interfaces cannot be configured on an Eth-Trunk member interface.
  • You are advised to add member interfaces to an Eth-Trunk and configure termination sub-interfaces on the Eth-Trunk in sequence. Termination sub-interfaces can be configured successfully on an Eth-Trunk only when all series of cards where member interfaces reside support termination sub-interfaces.
  • The VLAN IDs terminated by a sub-interface cannot be created in the system view or be displayed using a display command.
  • When VLAN IDs terminated by a sub-interface are used for Layer 3 forwarding, only the first VLAN takes effect even if multiple inner VLAN IDs are specified.
  • When VLAN IDs terminated by a sub-interface are used for Layer 3 forwarding, it is recommended that 128 VLANs be in all VLAN ranges.
  • VLAN termination sub-interfaces cannot be created on a VCMP client.
  • When the dot1q termination vid or qinq termination pe-vid ce-vid command is used to configure a VLAN for the VLAN termination sub-interface, the VLAN cannot be configured as the super-VLA or sub-VLAN.
  • If the PW-side interface is a Layer 3 interface switched by the undo portswitch command, the AC-side interface cannot be a Layer 3 interface or subinterface belonging to a Layer 3 interface; otherwise, traffic forwarding is abnormal.

Translation
Download
Updated: 2019-10-18

Document ID: EDOC1000178310

Views: 288372

Downloads: 141

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next