No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Configuration Guide - MPLS

S7700 and S9700 V200R011C10

This document describes MPLS configurations supported by the switch, including the principle and configuration procedures of static LSPs, MPLS LDP, MPLS TE, MPLS QoS, MPLS OAM, Seamless MPLS, and MPLS common features, and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the RSVP Message Format

Configuring the RSVP Message Format


You can adjust object information in RSVP messages by configuring the RSVP message format. In scenarios where an RSVP-TE tunnel is deployed, when devices from other vendors on the RSVP-TE tunnel use different format of RSVP message, you can modify the format of RSVP messages to be sent by the Huawei device to implement interworking.

You can configure the transit and egress nodes to add the down-reason object in an RSVP message to be sent, facilitating fault locating.


  • Configure the formats of objects in an RSVP message.

    Perform the following steps on each node of the MPLS TE tunnel:

    1. Run system-view

      The system view is displayed.

    2. Run mpls

      The MPLS view is displayed.

    3. Run mpls rsvp-te send-message { suggest-label | extend-class-type value-length-type | session-attribute without-affinity | down-reason }

      The formats of objects are specified for RSVP messages to be sent.

      The configuration guidelines of this command are as follows:

      • If a non-Huawei device requires the suggest-label object in a Path message sent by a Huawei device, specify suggest-label.

      • If a non-Huawei device uses the value-length-type (VLT) encoding format of the extended-class-type object but a Huawei device uses the type-length-value (TLV) encoding format of the extended-class-type object, specify extend-class-type value-length-type.

      • If a non-Huawei device does not support the session-attribute object sent by a Huawei device and the session-attribute object sent by the Huawei device has an affinity attribute, specify session-attribute without-affinity.

      • If you want an ingress to learn RSVP-TE tunnel Down causes of the transit and egress nodes, run the mpls rsvp-te send-message down-reason command.

  • Configure the format of the Record Route Object (RRO) in an Resv message.

    When the format in an Resv message sent by a non-Huawei device connected to the Huawei device is different from that on the Huawei device, run the following command to adjust the format of Resv messages on the Huawei device to be the same as that on the non-Huawei device to implement interworking.

    Perform the following configurations on the transit and egress nodes of an MPLS TE tunnel.

    1. Run system-view

      The system view is displayed.

    2. Run mpls

      The MPLS view is displayed.

    3. Run the following commands as required.

      • On a transit node, run the mpls rsvp-te resv-rro transit { { incoming | incoming-with-label } | { routerid | routerid-with-label } | { outgoing | outgoing-with-label } } * command.
      • On an egress, run the mpls rsvp-te resv-rro egress { { incoming | incoming-with-label } | { routerid | routerid-with-label } } * command.

Updated: 2019-10-18

Document ID: EDOC1000178315

Views: 118755

Downloads: 88

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Previous Next