No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Security

S7700 and S9700 V200R011C10

This document describes the configurations of Security, including ACL, reflective ACL, local attack defense, MFF, attack defense, traffic suppression and storm control, ARP security, port security, DHCP snooping, ND snooping, PPPoE+, IPSG, SAVI, URPF, keychain, separating the management plane from the service plane, security risks.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Setting the Time for Listing to an NA Packet in Response to Duplicate Addresses

(Optional) Setting the Time for Listing to an NA Packet in Response to Duplicate Addresses

Context

The time for listing to an NA packet in response to duplicate addresses can be set only in SLAAC-Only scenarios or DHCPv6+SLAAC scenarios.

  • In SLAAC-Only scenarios:

    When obtaining an IP address in SLAAC mode, an ND client generates the IPv6 address based on the prefix in the RA packet. After the IPv6 address is generated, the ND client sends an NS packet to check whether duplicate addresses exist on the network. When detecting the NS packet in the DAD process from the ND client, the device generates an ND snooping entry, sets the entry to the detect state, and listens to the mapping NA packet.

    • If a mapping NA packet is detected in the configured listening period, IPv6 address conflict occurs and the device deletes this ND snooping entry.
    • If no mapping NA packet is detected in the configured listening period, the IPv6 address is available and the device sets the ND snooping entry to the bound state. The device deletes the ND snooping entry only when the entry ages out. If automatic user status detection for users mapping ND snooping dynamic binding entries is enabled using the nd user-bind detect enable command on the device, and no NA packet is returned from the user after NS packets are sent for times configured using the nd user-bind detect retransmit retransmit-times interval retransmit-interval command, the device considers that the user is not online and deletes the mapping ND snooping entry.
  • In DHCPv6+SLAAC scenarios:

    • The procedure for processing packets by SAVI in SLAAC mode is the same as that in SLAAC-Only scenarios.

    • When obtaining an IP address in DHCPv6 mode, a DHCPv6 client may send an NS packet to check whether duplicate addresses exist on the network. When detecting the NS packet in the DAD process from the DHCPv6 client, the device sets the mapping DHCPv6 snooping entry to the detect state, and listens to the mapping NA packet.

      • If a mapping NA packet is detected in the configured listening period, IPv6 address conflict occurs and the device deletes this DHCPv6 snooping entry.
      • If no mapping NA packet is detected in the configured listening period, the IPv6 address is available and the device sets the DHCPv6 snooping entry to the bound state. The device deletes the DHCPv6 snooping entry only when detecting the DHCPv6 Decline packet or DHCPv6 Release packet from the DHCPv6 client.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run savi max dad-delay value

    Time for listing to an NA packet is set.

    By default, the time for listening to an NA packet is 2 seconds.

Translation
Download
Updated: 2019-04-01

Document ID: EDOC1000178319

Views: 136026

Downloads: 78

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next