No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
AS Direct Config

AS Direct Config

This section describes how to directly configure ASs on the parent.

Context

Choose Monitoring > Summary to check Member Device Status. Only normal ASs working in centralized configuration mode can be directly configured on the parent.

Procedure

  • Global AS configuration
    1. Choose Configuration > Advanced SVF Config > AS Direct Config to enter the AS Direct Config page.
    2. Click behind AS Name to select the AS to be configured and click OK to enter the configuration page. Click the Global Configuration tab, as shown in Figure 5-33.

      Figure 5-33  Global configuration page

      Table 5-22 describes parameters on the page.
      Table 5-22  Global configuration parameters

      Parameter

      Description

      Packet Rate Limit

      Source IP-based ARP rate limit (pps)

      Configures ARP rate limiting based on source IP addresses.

      Source MAC-based ARP rate limit (pps)

      Configures ARP rate limiting based on source MAC addresses.

      NOTE:

      This function is supported only when ASs are S6720S-EIs or S6720EIs.

      PoE
      NOTE:

      You can click PoE parameters to edit these parameters and click to complete the configuration. This information is displayed only on the PoE-supporting switches.

      Slot ID

      Specifies the slot ID of a PoE power module.

      IEEE 802.3af-compliant Power Supply

      Indicates whether IEEE 802.3af-compliant power supply is enabled:

      • ON: Enable IEEE 802.3af-compliant power supply.
      • OFF: Disable IEEE 802.3af-compliant power supply.

      Allow High Inrush Current During Power-on

      Indicates whether to enable a switch to allow high inrush current during power-on:

      • ON: Enable a switch to allow high inrush current during power-on.
      • OFF: Disable a switch from allowing high inrush current during power-on.
      Modify the slot ID
      NOTE:

      You can click a parameter in the Modify the slot ID area to edit its value, and click to complete the configuration.

      New Slot ID

      Configures the number of a slot on the AS.

    3. Configure the parameters and click Apply to complete the configuration.
  • Creating a voice VLAN
    1. Choose Configuration > Advanced SVF Config > AS Direct Config to enter the AS Direct Config page.
    2. Click behind AS Name to select the AS to be configured and click OK to enter the configuration page. Click Create, as shown in Figure 5-34.

      Figure 5-34  Creating a voice VLAN

    3. Enter the OUI address and subnet mask and click to complete the configuration.
  • Deleting a voice VLAN
    1. Choose Configuration > Advanced SVF Config > AS Direct Config to enter the AS Direct Config page.
    2. Click behind AS Name to select the AS to be configured and click OK to enter the configuration page.
    3. Select a voice VLAN in the list and click Delete.
    4. In the dialog box that is displayed, click OK.
  • AS interface configuration
    1. Choose Configuration > Advanced SVF Config > AS Direct Config to enter the AS Direct Config page.
    2. Click behind AS Name to select the AS to be configured and click OK to enter the configuration page. Click the Interface Configuration tab and select the interface to be configured, as shown in Figure 5-35.

      Figure 5-35  Interface configuration page

      When Configured as a Stack Port is selected, Table 5-23 describes parameters on the page.
      Table 5-23  Interface configuration parameters

      Parameter

      Description

      Logical stack port ID

      Specifies the logical stack port to which physical member ports are added.

      When Configured as a Stack Port is not selected, Table 5-24 describes parameters on the page.
      Table 5-24  Interface configuration parameters

      Parameter

      Description

      Ethernet Port

      Auto-Negotiation

      Indicates whether the auto-negotiation function is enabled:
      • ON: Enable the auto-negotiation function.
      • OFF: Disable the auto-negotiation function.

      Interface rate

      Sets the rate in non-auto-negotiation mode.
      NOTE:
      This parameter is valid only when Auto-Negotiation is set to OFF.

      Duplex mode

      Sets the duplex mode for an in non-auto-negotiation mode.
      NOTE:
      This parameter is valid only when Auto-Negotiation is set to OFF.

      Loop detection

      Indicates whether to enable loopback detection:
      • ON: Enable loopback detection.
      • OFF: Disable loopback detection.

      Port description

      Configures the description for an interface.

      PoE

      PoE

      Indicates whether to enable the PoE function. This parameter is available only when the online AS supports the PoE function.
      • ON: Enable the PoE function.
      • OFF: Disable the PoE function.

      Forcible power supply on ports

      Indicates whether forcible power supply is enabled on ports:
      • ON: Enable loopback detection.
      • OFF: Disable loopback detection.

      PD compatibility detection

      Indicates whether PD compatibility detection is enabled:
      • ON: Enable PD compatibility detection.
      • OFF: Disable PD compatibility detection.

      Power supply priority

      Sets the power supply priority of a PoE interface.

      Advanced

      Port bridge

      Indicates whether the port bridge function is enabled:
      • ON: Enable the port bridge function.
      • OFF: Disable the port bridge function.

      Electrical port sleeping

      Indicates whether to enable electrical port sleeping:
      • ON: Enable electrical port sleeping.
      • OFF: Disable electrical port sleeping.

      Loopback detection

      Indicates whether to enable loopback detection:
      • ON: Enable loopback detection.
      • OFF: Disable loopback detection.

      Loopback detection in a specified VLAN

      Performs loopback detection in a specified VLAN.

    3. Configure the parameters and click Apply to complete the configuration.
Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 83464

Downloads: 112

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next