No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
AP User-Side Service

AP User-Side Service

Procedure

  1. Choose Configuration > SVF Quick Config > AP User-Side Service. The Service Settings tab is displayed, as shown in Figure 5-22.

    Figure 5-22  Service Settings tab

  2. Click Create in the AP Group List pane. In the Create AP Group dialog box that is displayed, set AP group name and click OK.
  3. Create an SSID in an AP group.
    1. Click the Service Settings tab and set service parameters.
    2. Click Create. Set SSID parameters on the page that is displayed. For description of the parameters, see Table 5-8, Table 5-9, Table 5-10, and Table 5-11.



      Table 5-8  Basic SSID parameters

      Parameter

      Description

      SSID

      SSID name.

      Forwarding mode

      Data forwarding mode of the corresponding AP.

      Radio

      Radio to which a VAP is applied.

      WLAN ID

      VAP corresponding to the SSID.

      Table 5-9  VLAN and gateway parameters

      Parameter

      Description

      Service VLAN ID

      Service VLAN bound to the VAP mapping the SSID.
      • Click and select a service VLAN in the displayed Select window.
      • Click and create a service VLAN in the displayed Add VLAN and Gateway Configuration window.
      • Click and modify the existing service VLAN in the displayed Update VLAN And Gateway Configuration window.

      Gateway location

      Whether the Parent functions as the gateway.

      VLANIF (IP/mask)

      IP address of the VLANIF interface on the Parent, serving as the user gateway IP address.

      User IP allocated by

      Whether the IP addresses of STAs are obtained from the Parent or the server when the Parent functions as the gateway.

      Remote server address

      IP address of the remote server when it allocates IP addresses to STAs.

      This parameter is displayed when User IP allocated by is set to Remote server.

      Table 5-10  SSID security parameters

      Parameter

      Description

      Security Settings

      Security policy used on a wireless network.

      • High: WPA-WPA2 802.1X
      • Medium: WPA-WPA2 PSK
      • Low: OPEN

      Encryption mode

      Encryption mode of a security policy,

      which is valid only when Security Settings is set to High or Medium.

      Key type

      Key format of a security policy,

      which is valid only when Security Settings is set to Medium.

      Key/Confirm key

      Encryption key of a security policy,

      which is valid only when Security Settings is set to Medium.

      Table 5-11  SSID authentication parameters

      Parameter

      Description

      Authentication mode

      Authentication mode used by an STA that accesses a wireless network using the SSID.

      Server IP

      IP address of an external RADIUS server,

      which is valid only when Authentication mode is set to External RADIUS.

      Port number

      Port number of an external RADIUS server,

      which is valid only when Authentication mode is set to External RADIUS.

      Shared key/Confirm shared key

      Shared key of an external RADIUS server,

      which is valid only when Authentication mode is set to External RADIUS.

      Access mode

      Access mode of an external RADIUS server,

      which is valid only when Authentication mode is set to Local authentication or External RADIUS.

      External Portal Server

      External Portal server, which is valid only when Access mode is set to External Portal Server.

      • Server name: name of an external Portal server
      • Source IP: source IP address of an external Portal server
      • URL: interface URL of an external Portal server
      • Server IP: IP address of an external Portal server
      • Port number: port number of an external Portal server
      • Shared key/Confirm shared key: shared key of an external Portal server

    3. Click OK.
  4. Add an SSID to an AP group.
    1. Click the Service Settings tab and set service parameters.
    2. Click Add. Set SSID parameters on the page that is displayed. For description of the parameters, see Table 5-12.



      Table 5-12  SSID parameters

      Parameter

      Description

      Select SSID

      SSID that has been created in another AP group.

      Radio

      Radio associated with the SSID.

      WLAN ID

      VAP associated with the SSID.

    3. Click OK to complete the configuration.
  5. Remove an SSID from an AP group.
    1. Click the Service Settings tab and set service parameters.
    2. Select the SSID that you want to remove and click Remove.
    3. Click OK in the displayed window.
  6. Add existing APs to an AP group.

    You can manually set parameters on the web page to add existing APs to an AP group.

    1. Click the AP Manage tab and configure APs.
    2. Click Add. On the page that is displayed, set Mode to Select existing APs.



    3. Select APs from the list below, and click OK.
  7. Manually add APs to an AP group.

    This operation allows you to manually add a maximum of 10 APs offline to an AP group.

    1. Click the AP Manage tab and configure APs.
    2. Click Add. On the page that is displayed, set Mode to Manually add.



    3. Configure AP parameters. For description of the parameters, see Table 5-13.

      Table 5-13  Parameters for manually adding an AP

      Parameter

      Description

      Keyword

      AP authentication mode:

      • AP MAC: The AP authentication mode is MAC address authentication.
      • AP SN: The AP authentication mode is SN authentication.

      AP MAC

      MAC address of the new AP. This parameter is mandatory.

      AP ID

      ID of the new AP.

      This parameter is mandatory when Keyword is set to AP SN.

      AP type

      Type of the new AP.

      AP SN

      Serial number of the AP.

      This parameter is mandatory when Keyword is set to AP SN.

      NOTE:

      You can click to add a maximum of 10 APs manually.

    4. Click OK.
  8. Import APs using a template.

    This operation allows you to manually add multiple APs offline to an AP group.

    NOTE:

    If AP authentication mode is set to SN authentication, ensure that the AP SNs have been configured when importing APs offline.

    1. Click the AP Manage tab and configure APs.
    2. Click Add. On the page that is displayed, set Mode to Batch import.



    3. Click to download the batch import template to your local computer.
    4. Use the network planning and optimization tool to plan the network parameters and export the planned parameters to the AP information template. Table 5-14 describes the parameters of the AP information template.

      NOTE:

      If you download an AP information template of the Chinese web system under an English Windows operating system (OS), the Chinese characters in the AP information template cannot be displayed. You can choose Start > All Programs > Microsoft Office > Microsoft Office Tools > Microsoft Office 2003 Language Settings in the Windows OS (take Microsoft Office 2003 as an example) and set Primary Editing Language to Chinese(PRC) on the Editing Language tab. After completing the setting, restart the Microsoft Office Excel and open the AP information template. The Chinese characters in the template will be displayed normally.

      Table 5-14  Parameters of the AP information template

      Parameter

      Description

      AP ID

      AP ID. If an AP is imported not for the first time and the MAC address of the AP is not specified, the AP ID is mandatory; otherwise, the AP ID is optional.

      AP Name

      AP name. This parameter is optional.

      AP Type

      AP type. This parameter is optional.

      AP MAC

      MAC address of an AP. If the AP authentication mode is MAC address authentication, AP MAC must be set when the AP is imported for the first time or the AP ID is not specified.

      AP SN

      AP SN. If the AP authentication mode is SN authentication, AP SN must be set when the AP is imported for the first time.

      AP Group

      AP group. This parameter is optional.

      Radio ID

      Radio ID of the AP. This parameter is optional. If you set Channel, Band Width, or Power, Radio ID must be set.

      Channel

      Radio channel of the AP. This parameter is optional. If you set this parameter, Band Width and Radio ID must be set.

      Band Width

      Radio bandwidth of the AP. This parameter is optional. If you set this parameter, Channel and Radio ID must be set.

      Power

      Radio power of the AP. This parameter is optional. If you set this parameter, Radio ID must be set.

    5. Click to select the batch import template, then click Import.
    6. Click OK.
Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 84458

Downloads: 112

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next