Enter keywords to search.
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document.
Note: Even the most advanced machine translation cannot match the quality of professional translators.
Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
AS Profile Mgmt
AS Profile Mgmt
This section describes how to add AS profiles to an SVF
system.
Procedure
Create a network basic profile.
Choose and click the Network Basic Profile tab.
Click Create , as shown in Figure 5-28 .
Figure 5-28 Creating a network basic profile
Table 5-17 describes
parameters on the page.
Table 5-17 Parameters for creating a network basic profile
Parameter
Description
Profile Name
Specifies a profile name.
Default VLAN
Configures a default VLAN.
Allowed VLAN
Configures an allowed VLAN.
Voice VLAN
Configures a voice VLAN.
Add Voice VLAN to Untag VoIP
Specifies whether packets carry VLAN tags.
Configure the parameters and click to complete the
configuration.
Delete a network basic profile.
Choose and click the Network Basic Profile tab.
Select the required network basic profile and click Delete .
In the dialog box that is displayed, click OK .
Create a network enhanced profile.
Choose and click the Network Enhanced Profile tab.
Click Create , as shown in Figure 5-29 .
Figure 5-29 Creating a network enhanced profile
Table 5-18 describes
parameters on the page.
Table 5-18 Parameters for creating a network enhanced profile
Parameter
Description
Profile Name
Specifies a profile name.
Unknown Unicast Traffic Suppression (pps)
Sets the maximum rate of unknown unicast traffic.
Broadcast Traffic Suppression (pps)
Sets the maximum rate of broadcast traffic.
Multicast Traffic Suppression (pps)
Sets the maximum rate of multicast traffic.
DHCP Snooping
Indicates whether to enable DHCP snooping:
ON: Enable DHCP snooping.
OFF: Disable DHCP snooping.
IPSG
Indicates whether to enable IP packet check:
ON: Enable IP packet check.
OFF: Disable IP packet check.
NOTE: This parameter is valid only when DHCP Snooping is set to ON .
DAI
Indicates whether to enable dynamic ARP inspection.
ON: Enable dynamic ARP inspection.
OFF: Disable dynamic ARP inspection.
NOTE: This parameter is valid only when DHCP Snooping is set to ON .
All Traffic Suppression (kbps)
Sets the traffic rate limit.
Edge Port
Indicates whether to enable the edge port function:
ON: Enables the edge port function.
OFF: Disable the edge port function.
Configure the parameters and click to complete the
configuration.
Delete a network enhanced profile.
Choose and click the Network Enhanced Profile tab.
Select the required network enhanced profile and click Delete .
In the dialog box that is displayed, click OK .
Create a user access profile.
Choose and click the User Access Profile tab.
Click Create , as shown in Figure 5-30 .
Figure 5-30 Creating a user access profile
Table 5-19 describes
parameters on the page.
Table 5-19 Parameters for creating a user access profile
Parameter
Description
Profile Name
Specifies a profile name.
Bound Authentication Profile Name
Specifies the name of an authentication profile to be bound
to the user access profile.
NOTE: Choose to learn how to create an
authentication profile.
Number of Access Users
Sets the maximum number of access users.
ARP Packet Rate Limit (kbps)
Sets the rate limit of incoming ARP packets on an AS port.
NOTE: This parameter is valid when no value is set for Bound Authentication Profile Name .
DHCP Packet Rate Limit (kbps)
Sets the rate limit of incoming DHCP packets on an AS port.
NOTE: This parameter is valid when no value is set for Bound Authentication Profile Name .
Configure the parameters and click to complete the
configuration.
Delete a user access profile.
Choose and click the User Access Profile tab.
Select the required user access profile and click Delete .
In the dialog box that is displayed, click OK .
Create an AS administrator profile.
Choose and click the AS Administrator Profile tab.
Click Create , as shown in Figure 5-31 .
Figure 5-31 Creating an AS administrator profile
Table 5-20 describes
parameters on the page.
Table 5-20 Parameters for creating an AS administrator profile
Parameter
Description
Profile Name
Specifies a profile name.
User Name
Configures an AS administrator user name.
Password
Configures an AS administrator password.
ARP Rate Limit (kbps)
Sets the rate limit of outgoing ARP packets on an AS uplink
fabric-port.
DHCP Rate Limit (kbps)
Sets the rate limit of outgoing DHCP packets on an AS uplink
fabric-port.
Configure the parameters and click to complete the
configuration.
Delete an AS administrator profile.
Choose and click the AS Administrator Profile tab.
Select the required AS administrator profile and click Delete .
In the dialog box that is displayed, click OK .
Updated: 2019-10-17
Document ID: EDOC1000178323
Views: 87819
Downloads: 112
Average rating:
This Document Applies to these Products