No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Traffic Profile

Traffic Profile

Procedure

  • Create a traffic profile.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > Traffic Profile. The Traffic Profile List page is displayed.
    2. Click Create. The Create Traffic Profile page is displayed.
    3. Enter the name of the new traffic profile in Profile name.

      To copy all parameters from another profile to the new profile, select the name of the profile in Copy parameters from other profiles. If None is selected, parameters are not copied from another profile.

    4. Click OK. The parameter setting page of the new traffic profile is displayed.



    5. Set parameters for creating a traffic profile. Table 9-4 describes the parameters for creating a traffic profile.

      Table 9-4  Parameters for creating a traffic profile

      Parameter

      Description

      Traffic Profile

      Name of the traffic profile, which cannot be modified.

      User isolation mode

      User isolation mode.

      Multicast-to-unicast

      Whether to enable the function of converting multicast packets to unicast packets.

      You can enable the function of converting multicast packets to unicast packets in scenarios that have high requirements on multicast stream transmission, such as a high-definition video on-demand scenario. After the function is enabled, an AP listens on Report and Leave packets to maintain multicast-to-unicast entries. When sending multicast packets to the client, the AP converts the multicast packets to unicast packets based on the multicast-to-unicast entries to improve multicast stream transmission efficiency.

      IGMP-Snooping

      Whether to enable IGMP snooping.

      Multicast Report/Leave Suppression

      Whether to enable suppression of multicast Report/Leave packets.

      Broadcast packet rate limit

      Rate limit for broadcast packets. Broadcast packets are discarded if their rates exceed the rate limit.

      Multicast packet rate limit

      Rate limit for multicast packets. Multicast packets are discarded if their rates exceed the rate limit.

      Unknown unicast packet rate limit

      Rate limit for unknown unicast packets. Unknown unicast packets are discarded if their rates exceed the rate limit.

      Packet filtering

      Inbound ACL

      ACL used to filter incoming packets.

      Outbound ACL

      ACL used to filter outgoing packets.

      Re-marking

      Re-marking Incoming Packets

      Whether to re-mark the priority of incoming packets.

      Re-marking Outgoing Packets

      Whether to re-mark the priority of outgoing packets.

      Uplink Priority Mapping on Air Interface

      Mapping from the 802.11e user priority to DSCP priority in the CAPWAP header when packets are sent from an AP to an AC.

      Trust mode

      Trusted priority on the air interface, which is the 802.11e or DSCP priority.

      802.11e

      802.11e user priority.

      DSCP

      DSCP priority of 802.11 packets.

      Tunnel DSCP

      DSCP priority in the CAPWAP header.

      Downlink Priority Mapping on Air Interface

      Mapping from the 802.1p or DSCP priority of 802.3 packets to the 802.11e user priority when packets are sent to an AP from upper-layer devices.

      Trust mode

      Trusted priority on the air interface, which is the 802.1p or DSCP priority.

      802.1p

      802.1p priority of 802.3 packets.

      Tunnel DSCP

      DSCP priority in the CAPWAP header.

      802.11e

      802.11e user priority.

      Rate Limit

      STA uplink rate limit

      Uplink rate limit for a STA.

      STA downlink rate limit

      Downlink rate limit for a STA.

      VAP uplink rate limit

      Uplink rate limit for all STAs on a VAP. The value of this parameter must be greater than the uplink rate limit set for a STA.

      VAP downlink rate limit

      Downlink rate limit for all STAs on a VAP. The value of this parameter must be greater than the downlink rate limit set for a STA.

    6. Click Apply.
  • Modify a traffic profile.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > Traffic Profile. The Traffic Profile List page is displayed.
    2. Click the name of the traffic profile that you want to modify. The traffic profile configuration page is displayed.
    3. Set parameters for modifying a traffic profile. Table 9-4 describes the parameters for modifying a traffic profile.
    4. Click Apply.
  • Delete a traffic profile.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > Traffic Profile. The Traffic Profile List page is displayed.
    2. Select the profile that you want to delete and click Delete. In the Confirm dialog box that is displayed, click OK.
  • Display the profile reference relationship.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > Traffic Profile. The Traffic Profile List page is displayed.
    2. Select the profile of which you want to display the reference relationship and click Display Reference Relationship. The system displays the types and names of the objects that reference the profile.

      NOTE:

      Click Hide Reference Relationship. The system hides the displayed results.

Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 83476

Downloads: 112

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next