No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
AP Wired Port Profile

AP Wired Port Profile

Context

An AP wired port profile allows you to manage and configure wired interfaces of APs. You can configure wired port parameters in the AP wired port profile to facilitate AP management.

Procedure

  • Create an AP wired port profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
    2. Click Create. The Create AP Wired Port Profile page is displayed.
    3. Enter the name of the new AP wired port profile in Profile name.

      To copy all parameters from another profile to the new profile, select the name of the profile in Copy parameters from other profiles. If None is selected, parameters are not copied from another profile.

    4. Click OK. The parameter setting page of the new AP wired port profile is displayed.
    5. Set parameters for creating an AP wired port profile. Table 9-22 describes the parameters for creating an AP wired port profile.



      Table 9-22  Parameters for creating an AP wired port profile

      Parameter

      Description

      AP Wired Port Profile

      Name of the AP wired port profile, which cannot be modified.

      Enable Eth-trunk

      Whether to enable Eth-Trunk.

      Port mode
      Operating mode of a wired interface.
      • None: default mode

      • Root: root mode

      • Endpoint: endpoint mode

      • Middle: middle mode

      NOTE:
      By default,
      • On a common AP: Its GE interfaces work in root mode, Ethernet interfaces in endpoint mode, and Eth-Trunk interfaces in root mode.
      • On a central AP: Its uplink GE interfaces in root mode and downlink GE interfaces work in middle mode.
      • On an R230D: Its Ethernet interface works in root mode.
      • On an R240D: Its Ethernet interface works in endpoint mode and GE interface in root mode.
      • On an R250D, R250D-E, AP2050DN, and AP2050DN-E: Their uplink GE interfaces work in root mode and downlink GE interfaces in endpoint mode.
      • On an R450D: Its GE interface works in root mode.
      Port description

      Port description.

      User isolation mode

      User isolation mode on a wired interface.

      If Port mode is set to Endpoint, you need to set this parameter.

      STP

      Whether to enable STP on the wired interface.

      STP-triggered port shutdown

      Whether STP-triggered port shutdown is enabled on the AP's wired interface.

      Port recovery time (s)

      Auto-recovery interval for an AP's wired interface on which the STP-triggered port shutdown function is enabled.

      DHCP trusted port

      Whether to enable the DHCP trusted port function.

      IGMP Snooping

      Whether to enable the IGMP Snooping function.

      Address learning

      Whether terminal address learning is enabled on the AP's wired interface.

      IP packet binding check

      Whether IP packet binding check is enabled on the AP's wired interface.

      ARP packet binding check

      Whether dynamic ARP inspection (DAI) is enabled on the AP's wired interface.

      Port PVID

      PVID of the wired interface.

      Added VLAN ID

      ID of the VLAN to which the wired interface is added. An interface can join a VLAN in tagged or untagged mode.

      Packet Filtering
      Inbound ACL

      ACL for filtering incoming packets.

      Click . Search for and select an ACL in Inbound ACL.

      Outbound ACL

      ACL for filtering outgoing packets.

      Click . Search for and select an ACL in Outbound ACL.

      Re-marking

      Re-marking Incoming Packets

      Re-marks packets in the inbound direction.

      Re-marking Outgoing Packets

      Re-marks packets in the outbound direction.

      Storm Control
      Broadcast packet rate limit (pps) Maximum broadcast traffic volume allowed on the AP's wired interface.
      Unicast packet rate limit (pps) Maximum unknown unicast traffic volume allowed the AP's wired interface.
      Multicast packet rate limit (pps) Maximum multicast traffic volume allowed on the AP's wired interface.

    6. Click Apply. In the Info dialog box that is displayed, click OK.
  • Modify an AP wired port profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
    2. Click the name of the AP wired port profile that you want to modify. The AP Wired Port Profile page is displayed.
    3. Modify parameters of the AP wired port profile. Table 9-22 describes the parameters for modifying an AP wired port profile.
    4. Click Apply. In the Info dialog box that is displayed, click OK.
  • Delete an AP wired port profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
    2. Select the profile that you want to delete and click Delete. In the Confirm dialog box that is displayed, click OK.
  • Display the profile reference relationship.
    1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed.
    2. Select the profile of which you want to display the reference relationship and click Display Reference Relationship. The system displays the types and names of the objects that reference the profile.

      NOTE:

      Click Hide Reference Relationship. The system hides the displayed results.

  • Configure the profiles that are referenced by the AP wired port profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP Wired Port Profile. The AP Wired Port Profile List page is displayed. Click next to AP Wired Port Profile. The AP wired port profile name is displayed. Click next to the specified AP wired port profile to view the profiles that are referenced by the AP wired port profile.
    2. Click any profile referenced by the AP wired port profile. The configuration page of the referenced profile is displayed on the right. You can select another profile from the drop-down list and set the profile parameters. For descriptions of the profile parameters, see its configuration page.
    3. Click Apply. In the Info dialog box that is displayed, click OK.
Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 84225

Downloads: 112

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next