No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
AP Group

AP Group

AP Group

Context

The AP group function is used to configure multiple APs in batches. When multiple APs managed by an AC require the same configurations, you can add these APs to one AP group and configure the AP group to complete AP configuration.

NOTE:

For details about configurations of each profile bound to an AP group, see Profile.

Procedure

  • Create an AP group.
    1. Choose Configuration > Wireless Services > AP Group > AP Group. The AP Group page is displayed.
    2. Click Create. Set the parameters in Table 5-118.



      Table 5-118  Parameters for creating an AP group

      Parameter

      Description

      AP group name

      Name of the AP group

      Copy parameters from other groups

      Copy configuration parameters from other AP groups to the current AP group.

    3. Click OK.
  • Delete an AP group.
    1. Choose Configuration > Wireless Services > AP Group > AP Group. The AP Group page is displayed.
    2. Select the AP group that you want to delete and click Delete.
    3. Click OK.
  • Bind profiles to the AP group.
    1. Choose Configuration > Wireless Services > AP Group > AP Group. The AP Group page is displayed.
    2. Click an AP group name. On the AP group configuration page that is displayed, you can see the configurations of the AP group. See Profile for descriptions of the configuration profiles and Table 5-119 for details about the configuration parameters.

      Table 5-119  Configuration parameters of an AP group

      Parameter

      Description

      VAP Configuration

      Configures VAPs for AP groups: adds or removes VAP profiles for AP groups. After a VAP profile is added, the AP generates a VAP to implement basic WLAN services.

      For detailed parameters, see Wireless Service.

      Radio Management

      Configures radio parameters for AP groups, enabling the radios to work at the optimal performance.
      • Regulatory Domain Profile: configures the country code and DCA parameters for radios.
      • Radio 0/Radio 1/Radio 2: configures parameters for radios.

      For detailed parameters, see Radio Management. Configure radios describes parameters on the Radio 0, Radio 1, and Radio 2 pages.

      AP

      Configures system and interface parameters for AP groups.
      • AP System Profile: configures system parameters for AP groups.
      • AP Wired Port Settings: configures interface parameters for AP groups.
      • ETH-TRUNK Profile: configures interface parameters for AP groups.

      For detailed profile parameters, see AP. See AP Wired Port Profile for parameters of the ETH, GE, ETH-TRUNK and MultiGE profiles.

      Mesh

      Configures the Mesh function for AP groups.
      • Mesh Profile: adds or removes Mesh profiles for radios in AP groups.
      • Mesh Whitelist Profile: adds or removes Mesh whitelist profiles for radios in AP groups.

      For detailed parameters, see Mesh.

      WDS

      Configures the WDS function for AP groups.
      • WDS Profile: adds or removes WDS profiles for radios in AP groups.
      • WDS Whitelist Profile: adds or removes WDS whitelist profiles for radios in AP groups.

      For detailed parameters, see WDS.

      WIDS

      Configures the WIDS function for AP groups.

      For detailed parameters, see WIDS.

      WLAN Location

      Configures the location function for AP groups.

      For detailed parameters, see WLAN Location.

      Bluetooth Service

      Configures the bluetooth function for AP groups.

      For detailed parameters, see Bluetooth Service.

    3. Click Apply.
  • Configure radios.
    1. Choose Configuration > Wireless Services > AP Group > AP Group. The AP Group page is displayed.
    2. Click an AP group name. The AP group configuration page is displayed.
    3. Click ahead of Radio Management. Among the displayed items, click Radio 0, Radio 1, or Radio 2. The radio configuration page is displayed. For detailed parameters, see Table 5-120.



      Table 5-120  Radio parameters

      Parameter

      Description

      Radio 0 Settings (2.4G)/Radio 1 Settings (5G)/Radio 2 Settings (5G)

      Working status

      Whether the radio is enabled or disabled.

      Working mode
      Working mode of APs, which can be:
      • normal
      • monitor

      EIRP (dBm)

      Transmit power of a radio.

      Channel

      Working bandwidth and working channel of the radio.

      Antenna gain (dB)

      Antenna gain of the radio.

      Coverage distance (0.1 km)

      Radio coverage distance.

      Spectrum analysis

      Whether spectrum analysis is enabled on the radio.

      Switch to 5G

      Whether the working frequency of a radio is switched to the 5 GHz frequency band. Only radio 0 supports this parameter.

      Automatic channel optimization

      Whether to enable automatic channel selection.

      Automatic power optimization

      Whether to enable automatic transmit power selection.

      WIDS Control

      Device detection

      Whether the device detection function is enabled on the radio.

      Countermeasure of Unauthorized Devices

      Whether rogue device containment is enabled.

      Attack detection type

      Attack detection type. Multiple options can be selected.

    4. Click Apply.

Static Load Balancing Group

Context

The load balancing function applies to scenarios where there is a high degree of overlap between APs' coverage ranges. If APs engaged in load balancing are far from each other, a STA may connect to a distant AP, which affects wireless experience of users.

When the load difference between APs reaches the load difference threshold, some STAs may access the network slowly because the APs will reject access requests of STAs according to the load balancing algorithm. If a STA continues sending association requests to an AP, the AP allows the STA to associate when the number of consecutive association attempts of the STA exceeds the maximum number of rejection times.

In static load balancing mode, APs providing the same services are manually added to a load balancing group. When a STA needs to access a WLAN, it sends an Association Request packet to an AC through an AP. The AC determines whether to permit access from the STA according to a load balancing algorithm. The implementation of static load balancing must meet the following conditions.
  • If dual-band APs are used, traffic is load balanced among APs working on the same frequency band.
  • Each load balancing group supports a maximum of 16 AP radios.
  • Under the agile distributed network architecture composed of the central AP and RUs, you only need to add radios of the RUs to a static load balancing group.

Procedure

  • Create a static load balancing group.
    1. Choose Configuration > Wireless Services > AP Group > Static Load Balancing Group. The Static Load Balancing Group page is displayed.
    2. Click Create. Set the parameters in Table 5-121.



      Table 5-121  Parameters for creating a static load balancing group

      Parameter

      Description

      Static load balancing group name

      Name of the static load balancing group.

      Maximum number of rejections

      Maximum number of associations for the load balancing group

      When the load in a load balancing group is unbalanced, the AC rejects a STA's request for associating with an AP with heavy load, but does not keep rejecting. When the number of consecutive association requests of the STA exceeds the maximum value, the AP allows the STA to associate with the AP.

      Mode

      Static load balancing mode.

      Start threshold for load balancing (STA count)

      Start threshold for load balancing based on the number of STAs.

      Start threshold for load balancing (%)

      Start threshold for load balancing based on the channel utilization.

      Load difference threshold for load balancing

      Load difference threshold for load balancing.

      Optional Radio

      Radio of AP that can be added to the load balancing group.

      Selected Radio

      Radio of AP to be added to the load balancing group.

    3. Click OK.
  • Modify a static load balancing group.
    1. Choose Configuration > Wireless Services > AP Group > Static Load Balancing Group. The Static Load Balancing Group page is displayed.
    2. Click the static load balancing group name, find the desired static load balancing group on the displayed page, and modify parameters.
    3. Click OK.
  • Delete a static load balancing group.
    1. Choose Configuration > Wireless Services > AP Group > Static Load Balancing Group. The Static Load Balancing Group page is displayed.
    2. Select the static load balancing group and click Delete.
    3. Click OK.

    NOTE:

    Click Refresh to refresh the displayed static load balancing group information.

Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 85197

Downloads: 112

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next