No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
VAP Profile

VAP Profile

Context

The administrator needs to deliver service parameters to an AP so that the AP can provide network access services for wireless users. A VAP profile is a set of service parameters. You can configure different VAP profiles and deliver configurations in the profiles to APs to provide differentiated WLAN services.

Procedure

  • Create a VAP profile.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > VAP Profile. The VAP Profile List page is displayed.
    2. Click Create. The Create VAP Profile page is displayed.
    3. Enter the name of the new VAP profile in Profile name.

      To copy all parameters from another profile to the new profile, select the name of the profile in Copy parameters from other profiles. If None is selected, parameters are not copied from another profile.

    4. Click OK. The parameter setting page of the new VAP profile is displayed.



    5. Set parameters for creating a VAP profile. Table 9-1 describes the parameters for creating a VAP profile.

      Table 9-1  Parameters for creating a VAP profile

      Parameter

      Description

      VAP Profile

      Name of the VAP profile, which cannot be modified.

      Status

      Whether to enable the service mode of a VAP.

      VAP type

      VAP type.

      • If the type of a VAP is set to service, STAs connected to the VAP can only access network resources but not APs. Service VAPs are used in regular WLAN deployment scenarios.
      • If the type of a VAP is set to ap-management, STAs connected to the VAP can only access APs but not network resources. AP management VAPs are used in STA access and AP management scenarios.

      Service VLAN

      Service VLAN of a VAP.

      • When a specific VLAN is configured as the service VLAN of a VAP, STAs connected to the VAP join the same VLAN.
      • When VLANs in a VLAN pool are configured as service VLANs of a VAP, STAs connected to the VAP join different VLANs.

      Service VLAN ID

      ID of the service VLAN.

      VLAN Pool

      VLAN pool used for service VLANs.

      Forwarding mode

      Service forwarding mode.

      Band steering

      Whether to enable band steering.

      ARP probe

      Whether to enable dynamic ARP probing.

      IP binding check

      Whether to enable IP source guard on an AP.

      IP learning

      Whether to enable STA address learning.

      Strict IP learning

      Whether to enable strict STA IP address learning through DHCP.

      Dynamic blacklist of strict IP learning

      Whether to add STAs with bogus IP addresses to a dynamic blacklist.

      DHCP trusted interface

      Whether to enable the DHCP trusted port function on an AP.

      Appending Option 82

      Whether to enable an AP to insert the Option 82 field in DHCP packets sent from a STA.

      RID format

      Format of the remote-ID in the Option 82 field inserted in DHCP packets sent from a STA.

      CID format

      Format of the circuit-ID in the Option 82 field inserted in DHCP packets sent from a STA.

      MAC address format

      Format of the AP's MAC address in the Option 82 field.

      User-defined

      User-defined format in the Option 82 field.

      Effective after logout

      Whether to enable offline management VAP and antenna alignment VAP functions.

      Disable VAP periodically

      Whether to enable the scheduled VAP auto-off function.

      Disable VAP time setting at intervals

      Scheduled time during which a VAP is disabled.

      No traffic users off the assembly line Whether to enable the device to monitor user traffic and forcibly disconnect STAs without traffic.
      SNF Whether to enable agile distributed SFN roaming.
      Flood attack detection
      Broadcast flood attack detection Whether to enable the broadcast flood attack detection function.
      Attack threshold (pps) Rate threshold for broadcast flood attack detection.
      Adding attackers to the blacklist Whether to enable the broadcast flood blacklist function.

    6. Click Apply.
  • Modify a VAP profile.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > VAP Profile. The VAP Profile List page is displayed.
    2. Click the name of the VAP profile that you want to modify. The VAP Profile page is displayed.
    3. Set parameters for modifying the VAP profile. Table 9-1 describes the parameters for modifying a VAP profile.
    4. Click Apply.
  • Delete a VAP profile.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > VAP Profile. The VAP Profile List page is displayed.
    2. Select the profile that you want to delete and click Delete. In the Confirm dialog box that is displayed, click OK.
  • Display the profile reference relationship.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > VAP Profile. The VAP Profile List page is displayed.
    2. Select the profile of which you want to display the reference relationship and click Display Reference Relationship. The system displays the types and names of the objects that reference the profile.

      NOTE:

      Click Hide Reference Relationship. The system hides the displayed results.

  • Configure profiles referenced by a VAP profile.
    1. Choose Configuration > Wireless Services > Profile > Wireless Service > VAP. The VAP Profile List page is displayed. Click next to VAP Profile. The system displays names of the VAP profiles. Click next to a VAP profile name. The profiles referenced by the VAP profile are displayed in the menu navigation area.
    2. Click any profile referenced by the VAP profile. The configuration page of the referenced profile is displayed on the right. You can select another profile from the drop-down list and set the profile parameters. For descriptions of the profile parameters, see its configuration page.
    3. Click Apply. In the Info dialog box that is displayed, click OK.
Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 84155

Downloads: 112

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next