No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
AP System Profile

AP System Profile

Context

To centrally manage and maintain multiple APs, add these APs to a group, set parameters in an AP system profile, and then reference the AP system profile in the AP group view.

Procedure

  • Create an AP system profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP System Profile. The AP System Profile List page is displayed.
    2. Click Create. The Create AP System Profile page is displayed.
    3. Enter the name of the new AP system profile in Profile name.

      To copy all parameters from another profile to the new profile, select the name of the profile in Copy parameters from other profiles. If None is selected, parameters are not copied from another profile.

    4. Click OK. The parameter setting page of the new AP system profile is displayed.
    5. Set parameters for the AP system profile. Table 9-21 describes the parameters for creating an AP system profile.

      Figure 9-9  AP System Profile

      Table 9-21  Parameters for creating an AP system profile

      Parameter

      Description

      AP System Profile

      Name of the new AP system profile, which cannot be modified.

      Service holding upon link disconnection

      Whether to enable or disable service holding upon link disconnection.

      Offline AP permit access of new STAs

      Whether to enable or disable the APs in fault state to allow access of new STAs.

      Authentication-free new user access upon link disconnection Whether to enable the offline AP to allow access of new STAs.
      Role in mesh networking

      Role of an AP on the Mesh network.

      MPP active reselection

      Whether to enable or disable active MPP reselection.

      MTU

      Maximum transmission unit (MTU) on an Ethernet interface.

      Dual-link or N+1 Backup
      Configuration mode Link backup mode.
      Primary AC IP address Source address of the active AC.
      Backup AC IP address Source address of the standby AC.
      AC priority IP address of the primary AC.
      Peer AC IP address IP address of the backup primary AC.
      Active/Standby link switchover mode Active/standby link switchover mode.
      Number of probe packets Number of times Echo packets are probed in a statistical period.
      Start threshold of the PLR for triggering a link switchover(%) Start threshold for the packet loss rate during an active/standby switchover.
      Difference threshold of the PLR for triggering a link switchover(%) Gap threshold for the packet loss rate during an active/standby switchover.
      LLDP
      Delay of enabling LLDP

      Delay in re-enabling LLDP on APs.

      Working mode

      LLDP working mode on APs.

      Packet transmission delay

      Delay after which an AP sends LLDP packets to neighboring devices.

      Packet transmission interval

      Interval at which an AP sends LLDP packets to neighboring devices.

      TTL of packets

      Number of hold time intervals during which AP information can be saved on a neighboring device.

      Report neighbor information Whether to enable the LLDP neighbor report function for an AP.
      Interval for reporting neighbor information (s) Interval at which an AP reports LLDP neighbor information to an AC.
      Eapol
      Eapol-response packet conversion

      EAPoL-response packet conversion method.

      Eapol-response packet encapsulation

      EAPoL-response packet encapsulation method.

      Eapol-response MAC address

      Unicast MAC address of EAPoL-response packets.

      This parameter must be set when Eapol-response packet encapsulation is set to Unicast packets with specific MAC addresses.

      Eapol-start packet conversion

      EAPoL-start packet conversion method.

      Eapol-start packet encapsulation

      EAPoL-start packet encapsulation method.

      Eapol-start MAC address

      Unicast MAC address of EAPoL-start packets.

      This parameter must be set when Eapol-start packet encapsulation is set to Unicast packets with specific MAC addresses.

      AP Alarm
      Alarm suppression

      Whether to enable the alarm suppression function for APs.

      Alarm suppression interval

      Interval during which alarms are suppressed on APs.

      High temperature alarm threshold

      High temperature alarm threshold for APs.

      Low temperature alarm threshold

      Low temperature alarm threshold for APs.

      CPU usage alarm threshold

      CPU usage alarm threshold for APs.

      Memory usage alarm threshold

      Memory usage alarm threshold for APs.

      Log Backup
      IP address of the log backup server

      IP address of the log server.

      Log backup level

      Severity of AP logs to be backed up.

      Spectrum Analysis
      Server IP/port number

      IP address and port number of a spectrum server.

      Use AC for transparent data transmission

      Whether an AC is used for transparent data transmission:

      • OFF: Data is transmitted directly to the spectrum server

      • ON: Data is transmitted to the spectrum server through an AC.

      AC port number

      Port number used by an AC to receive the spectrum information (UDP packets) sent by an AP when the AC is used for transparent data transmission.

      Aging time of non-Wi-Fi devices

      Aging time of non-Wi-Fi devices on an AC during spectrum analysis.

      PoE Settings
      Maximum output power Maximum output power of the central AP.
      PoE reserved power percentage Percentage of reserved PoE power to the available PoE power on the central AP.
      Alarm threshold of PoE power consumption percentage Alarm threshold of PoE power consumption percentage.
      IEEE802.3af switching Whether to enable a central AP to provide PoE power in compliance with IEEE 802.3af.
      Allow high inrush current during power-on Whether to enable the central AP to allow high inrush current during power-on.
      Broadcast Suppression on AP's Wired Ports
      Protocol type Broadcast packet type supported on AP's wired ports.
      ARP traffic threshold ARP broadcast packet threshold on AP's wired ports.
      IGMP traffic threshold IGMP multicast packet threshold on AP's wired ports.
      ND traffic threshold ND broadcast packet threshold on AP's wired ports.
      Other traffic threshold Threshold for broadcast packets of types other than ARP and ND on AP's wired ports.
      Others
      Manage VLAN

      Management VLAN for APs.

      Dynamic blacklist aging time

      Aging time of a dynamic blacklist entry.

      STelnet

      Whether to allow or forbid STelnet login.

      Telnet

      Whether to allow or forbid Telnet login.

      Console

      Whether to allow or forbid console port login.

      SFTP

      Whether to allow or forbid SFTP login.

      Offline VAP management

      Whether to enable or disable the offline VAP management function.

      USB power supply Whether to enable the USB function of an AP.
      Antenna combined output

      Whether to enable or disable combined output of antenna signals.

      Only the AP9132DN supports this function.

      Working mode of the IoT card Connection type between IoT cards and APs.

    6. Click Apply. In the Info dialog box that is displayed, click OK.
  • Modify an AP system profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP System Profile. The AP System Profile List page is displayed.
    2. Click the name of the AP system profile that you want to modify. The AP System Profile page is displayed.
    3. Modify parameters of the AP system profile. For the parameter description, see Table 9-21.
    4. Click Apply. In the Info dialog box that is displayed, click OK.
  • Delete an AP system profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP System Profile. The AP System Profile List page is displayed.
    2. Select the profile that you want to delete and click Delete. In the Confirm dialog box that is displayed, click OK.
  • Display the profile reference relationship.
    1. Choose Configuration > Wireless Services > Profile > AP > AP System Profile. The AP System Profile List page is displayed.
    2. Select the profile of which you want to display the reference relationship and click Display Reference Relationship. The system displays the types and names of the objects that reference the profile.

      NOTE:

      Click Hide Reference Relationship. The system hides the displayed results.

  • Configure a profile referenced in an AP system profile.
    1. Choose Configuration > Wireless Services > Profile > AP > AP System Profile. The AP System Profile List page is displayed.
    2. In the navigation tree, click to the left of AP System Profile to expand the AP system profile list. Click to the left of an AP system profile name to view the names of the profiles referenced in the AP system profile.
    3. Click any profile referenced by the AP system profile. The configuration page of the referenced profile is displayed on the right. You can select another profile from the drop-down list and set the profile parameters. For descriptions of the profile parameters, see its configuration page.
    4. Click Apply. In the Info dialog box that is displayed, click OK.
Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 92869

Downloads: 123

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next