No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

S7700 and S9700 V200R011C10

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
VRRP

VRRP

IPv4

Procedure

  • Create a VRRP entry.
    1. Choose Configuration > Advanced Services > VRRP > IPv4 to access the IPv4 page. Click Create, as shown in Figure 5-100.

      Figure 5-100  Creating a VRRP entry

      Table 5-53 describes the parameters.

      Table 5-53  VRRP parameters

      Parameter

      Description

      VRID

      Indicates the VRID of a VRRP group.

      VLANIF

      Click to specify the VLANIF interface on which a VRRP group is created.

      Virtual IP

      Indicates the virtual IP address of a VRRP group. Click to add the virtual IP address.
      NOTE:
      The virtual IP address must be on the same network segment as the IP address of the VLANIF interface.

      Configuration priority

      Indicates the priority of a device in the VRRP group. A larger value indicates a higher priority.

      Observing port

      Indicates whether to enable association between VRRP and the interface status.

      • ON: Association between VRRP and the interface status is enabled.
      • OFF: Association between VRRP and the interface status is disabled.

      Interface name

      Click to specify the associated interface.

      NOTE:
      This parameter is available only when the value of Observing port is ON.

      Priority

      Indicates the value by which the priority of the associated interface increases or decreases. Click to specify the value.

      NOTE:
      This parameter is available only when the value of Observing port is ON.

    2. Set parameters and click OK.
  • Modify a VRRP entry.
    1. Choose Configuration > Advanced Services > VRRP > IPv4 to access the IPv4 page.
    2. Click Modify next to a data item to access the Modify VRRP page, as shown in Figure 5-101.

      Figure 5-101  Modify VRRP page

    3. Modify parameters and click OK.
  • Delete a VRRP entry.
    1. Choose Configuration > Advanced Services > VRRP > IPv4 to access the IPv4 page.
    2. Select a data item to be deleted and click Delete. In the dialog box that is displayed, click OK.
  • Refresh VRRP information.
    1. Choose Configuration > Advanced Services > VRRP > IPv4 to access the IPv4 page.
    2. Click Refresh to refresh the VRRP list.

IPv6

Procedure

  • Create a VRRP6 entry.
    1. Choose Configuration > Advanced Services > VRRP > IPv6 to access the IPv6 page. Click Create, as shown in Figure 5-102.

      Figure 5-102  Creating a VRRP6 entry

      Table 5-54 describes the parameters.

      Table 5-54  VRRP6 parameters

      Parameter

      Description

      VRID

      Indicates the VRID of a VRRP6 group.

      VLANIF

      Click to specify the VLANIF interface on which a VRRP6 group is created.

      Link local address

      Indicates the link local address.

      Virtual IP

      Indicates the virtual IP address of a VRRP6 group. Click to add the virtual IP address.
      NOTE:

      The virtual IP address must be on the same network segment as the IP address of the VLANIF interface.

      The first virtual IPv6 address of a VRRP6 group must be a link local address.

      Configuration priority

      Indicates the priority of a device in the VRRP6 group. A larger value indicates a higher priority.

    2. Set parameters and click OK.
  • Modify a VRRP6 entry.
    1. Choose Configuration > Advanced Services > VRRP > IPv6 to access the IPv6 page.
    2. Click Modify next to a data item to access the Modify VRRP6 page, as shown in Figure 5-103..

      Figure 5-103  Modify VRRP6 page

    3. Modify parameters and click OK.
  • Delete a VRRP6 entry.
    1. Choose Configuration > Advanced Services > VRRP > IPv6 to access the IPv6 page.
    2. Select a data item to be deleted and click Delete. In the dialog box that is displayed, click OK.
  • Refresh VRRP6 information.
    1. Choose Configuration > Advanced Services > VRRP > IPv6 to access the IPv6 page.
    2. Click Refresh to refresh the VRRP6 list.
Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178323

Views: 93073

Downloads: 123

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next