No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S9300, S9300E, and S9300X V200R011C10

This document describes the configuration of BFD, DLDP, VRRP, SmartLink, CFM, EFM, Y.1731 and MAC swap loopback to ensure reliability on the device.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Configuring VRRP Time Parameters

(Optional) Configuring VRRP Time Parameters

Context

You can set VRRP time parameters as needed. Table 3-7 lists applicable scenarios.

Table 3-7  Applicable scenarios of VRRP time parameters
Function Applicable Scenario
Interval at which VRRP Advertisement packets are sent The master in a VRRP group sends VRRP Advertisement packets to backups at intervals to notify that it is working properly. After the Master_Down_Interval timer expires, a new master is selected among the backups if the backups do not receive VRRP Advertisement packets.

Heavy network traffic or time differences on different devices may result in the backup status change due to timeout of VRRP Advertisement packets. When packets from the original master reach the new master, the status of the new master changes. You can increase the interval to solve this problem.

Interval at which gratuitous ARP packets are sent by the master To ensure that MAC address entries on the downstream switch are correct, the master in a VRRP group periodically sends gratuitous ARP packets to update MAC address entries on the downstream switch.
Delay before a VRRP group recovers On an unstable network, frequent flapping of the BFD session status or interface status monitored by a VRRP group may result in frequent switching of the VRRP group status. After the delay is set, the VRRP group does not immediately respond to an interface or BFD session Up event. Instead, the VRRP group processes this event after the delay. This prevents frequent switching of the VRRP group status.

Procedure

  • Set the interval at which VRRP Advertisement packets are sent.
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The interface view is displayed.

    3. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    4. Run vrrp vrid virtual-router-id timer advertise advertise-interval

      The interval at which VRRP Advertisement packets are sent is set.

      By default, the interval is 1 second.

  • Set the interval at which gratuitous ARP packets are sent by the master.
    1. Run system-view

      The system view is displayed.

    2. Run vrrp gratuitous-arp timeout time

      The interval at which gratuitous ARP packets are sent by the master is set.

      By default, the master sends gratuitous ARP packets every 120s.

      NOTE:

      The interval at which the master sends gratuitous ARP packets must be shorter than the aging time of ARP entries on user devices.

      • To restore the default interval at which gratuitous ARP packets are sent, run the undo vrrp gratuitous-arp timeout command in the system view.

      • If the master does not need to send gratuitous ARP packets, run the vrrp gratuitous-arp timeout disable command in the system view.

  • Set the delay before a VRRP group recovers.
    1. Run system-view

      The system view is displayed.

    2. Run vrrp recover-delay delay-value

      The delay before a VRRP group recovers is set.

      By default, the delay before a VRRP group recovers is 0.

      NOTE:
      • After this command is used, all VRRP groups on the device are configured with the same delay.

      • When the device in a VRRP group restarts, VRRP status flapping will occur. It is recommended that the delay be set based on actual networking.

Translation
Download
Updated: 2019-04-17

Document ID: EDOC1000178423

Views: 91097

Downloads: 25

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next