No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Installation Guide

OceanStor 5000, 5000F, 6000, and 6000F V5 Series V500R007

This document is applicable to OceanStor 5110 V5, 5110F V5, 5300 V5, 5300F V5, 5500 V5, 5500F V5, 5600 V5, 5600F V5, 5800 V5, 5800F V5, 6800 V5, and 6800F V5 storage systems. It describes hardware installation of those storage systems for helping you easily and quickly finish the installation.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing a High-Density Disk Enclosure into a Cabinet

Installing a High-Density Disk Enclosure into a Cabinet

Install the high-density disk enclosure by sliding it into the cabinet, securing it, and checking the installation.

Prerequisites

Ensure that the following conditions are met before installing high-density disk enclosure:

  • The installation environment meets requirements.
  • Ensure that ball bearing guide rails used for sliding high-density disk enclosure into cabinets have been installed.

Ensure that the following tools and materials are available and ready for use:

  • Phillips screwdriver
  • M6 screw
  • M4 screw
  • M3 screw
  • Protective gloves
  • High-density disk enclosure

Precautions

To prevent personal injury and device damage, use at least three persons to carry and install the unloaded enclosure into the cabinet and install disks modules into the enclosure.

If you remove disks to facilitate the movement and installation of the device, record the mapping between each disk and its slot in advance. That helps insert each disk back to its correct slot after the movement and installation.

  • Install components into a cabinet from bottom to top to prevent the cabinet from falling over.
  • If a high-density disk enclosure is installed in the top 4 U space, disks cannot be inserted.

Procedure

  1. Wear protective gloves.
  2. Install the inner rail to the right of the high-density disk enclosure.

    1. Install the inner rail onto the system enclosure, as shown in step 1 in Figure 5-82.
      Figure 5-82 Install the inner rail

    2. Use two M4 screws to secure the inner rail, as shown in step 2 in Figure 5-82.

  3. Install the inner rail to the left of the high-density disk enclosure.

    Repeat Step 2 to install the left inner rail.

  4. Remove the two M3 screws from the upper panel, as shown in Figure 5-83.

    Figure 5-83 Removing screws

  5. Place the side step in the rear of the high-density disk enclosure on the front bracket of the ball bearing guide rails, and slide the disk enclosure into the cabinet along the ball bearing guide rails (no manual alignment is required because the inner rail automatically connects to the middle rail), as shown in Figure 5-84.

    • Do not pull out the middle guide rails when sliding the high-density disk enclosure into the cabinet. Otherwise, the guide rails may misalign.
    • Before you install disk modules, install the high-density disk enclosure into the cabinet.
    Figure 5-84 Sliding the high-density disk enclosure into a cabinet

  6. Check the high-density disk enclosure installation.

    • After sliding the high-density disk enclosure into the cabinet, pull out the high-density disk enclosure from the cabinet and slide the high-density disk enclosure into the cabinet for two times respectively to check that the ball bearing guide rails are correctly installed.
    • If you cannot push or pull out a high-density disk enclosure smoothly, check whether inner rails are fully inserted into mid rails. If the inner rails are not fully inserted into mid rails, disassemble the high-density disk enclosure and check whether ball bearing guide rails meet the following conditions according to the section of Installing Ball Bearing Guide Rails (for High-Density Disk Enclosures):
      • Check whether ball bearing guide rails are installed horizontally (whether front and back brackets of ball guide rails are on the same level).
      • Check whether the installation templates of ball bearing guide rails can be inserted.
      • Check whether the ball of the ball bearing guide rail is placed at the most front end of the middle rail.
      • Check whether the mid rails of ball bearing guide rails are completed inserted.

  7. Install a cover.

    1. Pull out the enclosure slowly, as shown in step 1 in Figure 5-85.
    2. Push the upper cover backward until the upper cover touches the mounting bars, as shown in step 2 in Figure 5-85.
    3. Fasten the two captive screws on the cover, as shown in step 3 in Figure 5-85.
    Figure 5-85 Installing a cover

  8. Install the system enclosure.

    1. Slide the enclosure into the cabinet slowly, as shown in step 1 in Figure 5-86.
    2. Fasten the two captive screws on the panel, as shown in step 2 in Figure 5-86.
    Figure 5-86 Fastening the two screws on the panel

  9. Repeat Step 2 to Step 8 to install other high-density disk enclosures into the cabinet.
Translation
Download
Updated: 2019-07-11

Document ID: EDOC1000181531

Views: 93728

Downloads: 871

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next