No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Installation Guide

OceanStor 5000, 5000F, 6000, and 6000F V5 Series V500R007

This document is applicable to OceanStor 5110 V5, 5110F V5, 5300 V5, 5300F V5, 5500 V5, 5500F V5, 5600 V5, 5600F V5, 5800 V5, 5800F V5, 6800 V5, and 6800F V5 storage systems. It describes hardware installation of those storage systems for helping you easily and quickly finish the installation.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Setting the GSM Modem

(Optional) Setting the GSM Modem

After setting the GSM modem, you can configure short message notification in management software. The storage system will send alarm information to a specified mobile phone. You can learn about storage system exceptions and solve them in a timely manner.

Prerequisites

You need to connect the storage device with a GSM modem, make sure you have installed GSM modem.

Context

  • If the GSM modem is not hot-swappable, do not insert or remove it when it is running.
  • If the storage system is enabled with short message notification, the serial port on the controller enclosure serves only the GSM.
  • For a storage system with eight or more controllers, GSM modems can only be configured for the first eight controllers.
  • For a 2 U controller enclosure, you are advised to connect the GSM modem to the serial port of controller A. If the serial port of controller A fails, connect the GSM modem to the serial port of controller B.
  • For a 3 U or 6 U controller enclosure, you are advised to connect the GSM modem to the serial port of the management modules 0. If the serial port of the management modules 0 fails, connect the GSM modem to the serial port of the management modules 1.

To demonstrate how to configure a GSM modem, the COM1 serial port (baud rate = 115200 bit/s) on the host and the DB9 serial port on the GSM modem (default baud rate = 9600 bit/s) is used as an example.

Procedure

  1. Insert a SIM card into the GSM modem.
  2. Connect GSM modem to the maintenance terminal serial port through a DB9 serial cable.
  3. Put the power cable of the GSM modem into the power supply outlet, then power on the GSM modem.

    If the red indicator blinks, the GSM modem is successfully installed.

  4. Run PuTTY. In the Category navigation tree, choose Session > Logging. The Basic options for your PuTTY session page for configuring the GSM modem is displayed, as shown in Figure 10-23.

    Figure 10-23 Page for Basic options for your PuTTY session

  5. Click Open.
  6. Run the at command on the COM1-PuTTY, and OK appears in the output if the GSM modem has connected to the host through the serial port. If this is true, go to Step 9. If running that command responds with nothing, the GSM modem has been disconnected from the serial port. If this is true, go to Step 7.
  7. Re-log in to the page for configuring the GSM modem, as shown in Figure 10-24.

    Figure 10-24 Page for configuring the GSM modem

  8. Reset the baud rate of the GSM modem until running the at command responds with OK.

    NOTE:
    • If the baud rate of the GSM modem is not confirmed, reconfigure it to ensure that the baud rate of the GSM modem and that of the serial port are consistent. In this condition, the PuTTY can be used to configure the GSM modem.
    • The baud rate can be configured using the command at+ipr=115200.

  9. Configure other parameters, for example whether to reply automatically.
  10. Click OK to save and exit. To verify the configuration, the following shows the configuration success page.

     
    at 
    OK 
    at+ipr=115200 
    OK 
    ats0=1 
    OK 
    at&w 
    OK     

  11. Upon successful configuration, connect the GSM modem to the serial port of the storage system for use.

    NOTE:

    For details about configuring the GSM modem, see the corresponding manual supplied with the GSM modem.

Translation
Download
Updated: 2019-07-11

Document ID: EDOC1000181531

Views: 94033

Downloads: 873

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next