drvfc showportinfo
Function
The drvfc showportinfo command is used to view the port information about the interface module of Pangea 8 Gbit/s Fibre Channel driver.
Format
drvfc showportinfo
Parameters
None
Views
Diagnostic view
Usage Guidelines
None
Example
View the port information about the interface module of Pangea 8 Gbit/s Fibre Channel driver.
admin:/diagnose>drvfc showportinfo
port | mode |state|plnk tlnk | Rate | WWPN |MultiDMA|MSI|TCQ|NCQ|Topology|
0x110000 | COM | open| 0 ,LOST | NoLink(0) | 20005439dfc9a015 | ON | ON|OFF|OFF| 5( 15)|
|LossOfSignal|Bad RX Char|Loss of Sync|Link Fail| RxEOFa |DisFrame|Bad CRC|Proto error|
| 0| 0| 0| 0| 0| 0| 0| 0|
--------------------------------------------------------------------------------------------------
port | mode |state|plnk tlnk | Rate | WWPN |MultiDMA|MSI|TCQ|NCQ|Topology|
0x110001 | COM | open| 0 ,LOST | NoLink(0) | 20015439dfc9a015 | ON | ON|OFF|OFF| 5( 15)|
|LossOfSignal|Bad RX Char|Loss of Sync|Link Fail| RxEOFa |DisFrame|Bad CRC|Proto error|
| 0| 0| 0| 0| 0| 0| 0| 0|
--------------------------------------------------------------------------------------------------
port | mode |state|plnk tlnk | Rate | WWPN |MultiDMA|MSI|TCQ|NCQ|Topology|
0x110002 | COM | open| 0 ,LOST | NoLink(0) | 20025439dfc9a015 | ON | ON|OFF|OFF| 5( 15)|
|LossOfSignal|Bad RX Char|Loss of Sync|Link Fail| RxEOFa |DisFrame|Bad CRC|Proto error|
| 0| 0| 0| 0| 0| 0| 0| 0|
--------------------------------------------------------------------------------------------------
port | mode |state|plnk tlnk | Rate | WWPN |MultiDMA|MSI|TCQ|NCQ|Topology|
0x110003 | COM | open| 0 ,LOST | NoLink(0) | 20035439dfc9a015 | ON | ON|OFF|OFF| 5( 15)|
|LossOfSignal|Bad RX Char|Loss of Sync|Link Fail| RxEOFa |DisFrame|Bad CRC|Proto error|
| 0| 0| 0| 0| 0| 0| 0| 0|
System Response
The following table describes the parameter meanings.
Parameter |
Meaning |
|---|---|
port |
Port ID. |
mode |
Port properties. |
state |
Port status. |
plnk |
Whether the synchronization signal is normal. |
tlnk |
Whether link negotiation is normal. |
Rate |
Working rate. |
WWPN |
Port world wide name (WWN). |
MultiDMA |
Whether MultiDMA is enabled. |
MSI |
Whether MSI is enabled. |
TCQ |
Whether TCQ is enabled. |
NCQ |
Whether native command queuing (NCQ) is enabled. |
Topology |
Port topology mode (working mode or configuration mode). |
LossOfSignal |
Count of lost signals. |
Bad RX Char |
Count of received incorrect characters. |
Loss of Sync |
Count of lost synchronization. |
Link Fail |
Count of link failures. |
RxEOFa |
Count of received EOFas. |
DisFrame |
Count of lost frames. |
Bad CRC |
Count of incorrect cyclic redundancy checks (CRCs). |
Proto error |
Count of incorrect protocols. |
Previous
