No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Advanced O&M Command Reference

OceanStor 2800 V5 V500R007

This document is applicable to OceanStor 2800 V5. Based on the CLI, this document describes how to use various commands classified by functions and how to set the CLI and manage the storage system through these commands. The document that you browse online matches the latest C version of the product. Click Download to download documents of other C versions.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
show remote_replication service_pair

show remote_replication service_pair


The show remote_replication service_pair command is used to show the service information about a remote replication.


show remote_replication service_pair service_id=? [ controller=? ]





service_id=? Service ID of the remote replication.

To obtain the value, run "show remote_replication feature_pair".

controller=? ID of the controller.

The value is in the format of XA or XB. X is an integer ranging from 0 to the value of the number of controller pairs minus 1.


Developer view

Usage Guidelines



To show the service information about remote replication "0", run the following command:

developer:/>show remote_replication service_pair service_id=0 controller=0A
Service ID : 0
Is Used : 1
Service Flag : 1
Back Ground Flag : 1
Synchronize Prepare State : 1
Feature Local ID : 0
Feature Type : 1
Service Type : 1
Is Primary : 0
Read Write Property : No access
Work Mode : 2
Rollback Type : 2
Local Object ID : 0
Local Object Resource Type : 40
DCL ID : 101
Remote Object ID : 0
Remote Object Resource Type : 40
Array ID : 0
Consistent Need Rollback : 0
Data State : 2
Is Initial SyncDone : 1
Servive State : Single
Rollback State : None
Snap SN : 7
Synchronizing Snap ID : --
Synchronizing Snap Time Point : --
Consistent Snap Time Point : 46327
Consistent Snap ID : 88235808129024
Consistent Snap SN : 7
Add Fail Time Point : --
Add Fail Time Point Type : 255
Difference End Time Point : --
Difference Start Time Point : --
Current Opcode : 4294967295
Valid Flag : 0
Log ID : 0
New Flag : 0
Delete Fail Snap ID : --
Delete Fail Snap Time Point : --

System Response

The following table describes the parameter meanings.



Service ID

Service ID of a remote replication pair.

Is Used

Whether a remote replication pair is used.

Service Flag

Flag of service start.

Back Ground Flag

Flag of background job start.

Synchronize Prepare State

Preparation status of synchronization start.

Feature Local ID

Local ID of a feature.

Feature Type

Feature type.

Service Type

Service type.

Is Primary

Primary disk array or not.

Read Write Property

Read/Write status.

Work Mode

Remote replication mode, synchronous or asynchronous.

Rollback Type

Rollback status.

Local Object ID

Local object ID.

Local Object Resource Type

Local resource type.



Remote Object ID

Remote object ID.

Remote Object Resource Type

Remote resource type.

Array ID

Disk array ID.

Consistent Need Rollback

Whether secondary site data needs to be rolled back for data consistency.

Data State

Data status.

Is Initial SyncDone

Whether initial synchronization is complete.

Servive State

Service status.

Rollback State

Rollback status.

Snap SN

Snapshot SN.

Synchronizing Snap ID

ID of a snapshot created in synchronization.

Synchronizing Snap Time Point

Time when a snapshot is created in synchronization.

Consistent Snap Time Point

Time when a consistency snapshot is created.

Consistent Snap ID

Consistency snapshot ID.

Consistent Snap SN

Consistency snapshot SN.

Add Fail Time Point

Time when adding a snapshot fails.

Add Fail Time Point Type

Type of the point in time that fails to be added.

Difference End Time Point

Time when difference record ends.

Difference Start Time Point

Time when difference record starts.

Current Opcode

Current operation code.

Valid Flag

Log information validity flag.

Log ID

Log ID.

New Flag

Flag of logs before being stored in databases. The parameter is replaced with parameter validFlag after logs are stored in databases.

Delete Fail Snap ID

ID of a snapshot that fails to be deleted.

Delete Fail Snap Time Point

Time of a snapshot that fails to be deleted.

Updated: 2020-01-17

Document ID: EDOC1000181575

Views: 729471

Downloads: 32

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next