showphy
Example
Display the information about the current link status.
PANGEA_SES:>showphy --------------------- phys stat --------------------- log_phy phys_phy chip_phy init_pass init_sw mabc_en dev_p sas sata rate rst_lim type 0 9 9 0 0 1 0 0 0 0 0 3 1 4 4 1 0 1 1 1 0 4 0 3 2 3 3 0 0 1 0 0 0 0 0 3 3 11 11 0 0 1 0 0 0 0 0 3 4 10 10 0 0 1 0 0 0 0 0 3 5 6 6 1 0 1 1 1 0 4 0 3 6 1 1 0 0 1 0 0 0 0 0 3 7 7 7 0 0 1 0 0 0 0 0 3 8 8 8 0 0 1 0 0 0 0 0 3 9 2 2 1 0 1 1 1 0 4 0 3 10 0 0 0 0 1 0 0 0 0 0 3 11 5 5 0 0 1 0 0 0 0 0 3 12 35 35 0 1 0 0 0 0 0 0 4 13 34 34 0 1 0 0 0 0 0 0 4 14 33 33 0 1 0 0 0 0 0 0 4 15 32 32 0 1 0 0 0 0 0 0 4 16 31 31 0 1 0 0 0 0 0 0 4 17 30 30 0 1 0 0 0 0 0 0 4 18 29 29 0 1 0 0 0 0 0 0 4 19 28 28 0 1 0 0 0 0 0 0 4 20 27 27 0 1 0 0 0 0 0 0 4 21 26 26 0 1 0 0 0 0 0 0 4 22 25 25 0 1 0 0 0 0 0 0 4 23 24 24 0 1 0 0 0 0 0 0 4 24 20 20 0 1 0 0 0 0 0 0 4 25 21 21 0 1 0 0 0 0 0 0 4 26 22 22 0 1 0 0 0 0 0 0 4 27 23 23 0 1 0 0 0 0 0 0 4 28 12 12 1 0 1 1 1 0 8 0 1 29 13 13 1 0 1 1 1 0 8 0 1 30 14 14 1 0 1 1 1 0 8 0 1 31 15 15 1 0 1 1 1 0 8 0 1 32 16 16 0 1 0 0 0 0 0 0 4 33 17 17 0 1 0 0 0 0 0 0 4 34 18 18 0 1 0 0 0 0 0 0 4 35 19 19 0 1 0 0 0 0 0 0 4
System Response
The following table describes the parameter meanings.
Parameter |
Meaning |
---|---|
log_phy | Logical phy index. |
phys_phy | Physical phy index. |
chip_phy | Chip phy index. |
init_pass | Initialization status of phy links. 1 indicates init passed. 0 indicates init not passed. |
init_sw | Whether phy is in the OOB_COMINIT state. 1 indicates that phy is in the OOB_COMINIT state. 0 indicates that phy is not in the OOB_COMINIT state. |
mabc_en | Whether phy is isolated by user commands. 1 indicates that phy is not isolated by user commands. 0 indicates that phy is isolated by user commands. |
dev_p | Whether phy is connected to another device.1 indicates that phy is connected to another device. 0 indicates that phy is not connected to another device. |
sas | Type of the device connected to phy. 1 indicates a SAS device. 0 indicates a non SAS device. |
sata | Type of the device connected to phy. 1 indicates a SATA device. 0 indicates a non SATA device. |
rate | Phy speed. 0 indicates that the data transfer rate is 0. 1 indicates 1.5 Gbit/s. 2 indicates 3 Gbit/s. 4 indicates 6 Gbit/s. 8 indicates 12 Gbit/s. |
rst_lim | Phy reset limit flag. 0 indicates that the flag is not set and 1 indicates that the flag is set. |
type | Phy type. 1 indicates up link phy, 2 indicates down link phy, 3 indicates disk phy, and 4 indicates reserved. |