No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Advanced O&M Command Reference

OceanStor 5000, 5000F, 6000, and 6000F V5 Series V500R007

This document is applicable to OceanStor 5110 V5, 5110F V5, 5300 V5, 5500 V5, 5600 V5, 5800 V5, 6800 V5, 5300F V5, 5500F V5, 5600F V5, 5800F V5, and 6800F V5. Based on the CLI, this document describes how to use various commands classified by functionsand how to set the CLI and manage the storage system through these commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
change hyper_metro_pair cfg_switch

change hyper_metro_pair cfg_switch


The change hyper_metro_pair cfg_switch command is used to modify the switch status of configuration synchronization for a specified HyperMetro pair.


change hyper_metro_pair cfg_switch pair_id=? partition_type=? option_type=? switch=?






HyperMetro pair ID.

Run the "show hyper_metro_pair general" command to obtain the value.


Type of a configuration synchronization partition.

  • "nfs_share": NFS share partition.
  • "smb_share": SMB share partition.
  • "quota": quota partition.
  • "fs_cfg": file system configuration partition.


Option type ID.

  • For an NFS share partition, the value is "0".
  • For an SMB share partition, the value is "0" or "1".
  • For a quota partition, the value is "0".
  • For a file system configuration partition, the value is "0" or "1".


Switch status.

The value can be "on" or "off".


Developer view

Usage Guidelines

Run this command under the guidance of R&D engineers. Modifying the switch status may result in inconsistency of active and standby configurations. Modify the switch status only when the link status is normal.


Modify the switch status of the configuration synchronization partition for a specified HyperMetro pair. The pair ID is "200bc79b99520000", partition_type is "NFS_share", option_type is "0", and the switch status is "Off".

developer:/>change hyper_metro_pair cfg_switch pair_id=200bc79b99520000 partition_type=nfs_share option_type=0 switch=off 
DANGER: You are about to perform maintenance on the HyperMetro configuration. This operation will lead to the inconsistency of user configuration between the two end of a HyperMetro pair. When the HyperMetro pair link is normal, this operation can change the status of the HyperMetro pair configuration synchronization switch to "enabled" or "disabled". The switch is enabled by default. When the switch is disabled, user's configuration on the local end of the HyperMetro pair only takes effect on the local end and will not be synchronized to the remote end. User configuration is not forbidden on the remote end. 
Suggestion: Before the operation, contact the engineers and perform all the operations under their guidance. Besides, confirm that: 
1. No other user is performing configuration on the system. 
2. The input operation parameters are correct.Have you read danger alert message carefully?(y/n)y 
Are you sure you really want to perform the operation?(y/n)y 
Command executed successfully.

System Response


Updated: 2019-07-11

Document ID: EDOC1000181619

Views: 633966

Downloads: 253

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Previous Next