No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Parts Replacement

OceanStor V5 Series V500R007

This document is applicable to OceanStor 5110 V5, 5110F V5, 5300 V5, 5300F V5, 5500 V5, 5500F V5, 5600 V5, 5600F V5, 5800 V5, 5800F V5, 6800 V5, 6800F V5, 18500 V5, 18500F V5, 18800 V5, and 18800F V5. This document describes the procedure for replacing the parts of storage system in terms of safety operations, preparations, and precautions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Replacing a Power Module (High-Density Disk Enclosure)

Replacing a Power Module (High-Density Disk Enclosure)

This section describes how to replace a power module.

Impact on the System

System reliability is compromised during power module replacement.

Prerequisites

  • The spare part of the power module is ready.
  • The power module that you want to replace has been located.
NOTE:

You can locate a component in either of the following ways:

  • Log in to DeviceManager and go to the System page. On the System page, check the device view and locate the position of the component to be replaced. If the component has a location indicator, turn on the indicator. (For details about how to turn on a location indicator, see the online help of DeviceManager.)
  • Use the alarm indicator of the component to locate its position.

Precautions

  • Do not touch the connectors of a power module and power cable.
  • Remove and insert a power module with even force. Excessive force may damage the appearance or connectors.
  • Remove only one power module at a time.
  • Shorten the duration of replacing a power module where possible.

Tools and Materials

  • ESD wrist strap
  • ESD bag
  • Label

Procedure

  1. Check status before replacement.

    1. Check system status.

      Start SmartKit and choose Home > Storage > Routine Maintenance > Health Check. On the Health Check page, perform inspection as instructed. For details, see Checking System Status.

      NOTE:

      If some items fail in the inspection, rectify the faults by performing the recommended actions in the inspection reports. Ensure that all other parts except the parts to be replaced are working properly.

    2. Check the status of the parts to be replaced.

      Start SmartKit and choose Home > Storage > Parts Replacement > Parts Replacement. On the Parts Replacement page, click FRU Replacement. Then complete the check before the replacement as prompted. For details, see Replacing an FRU.

    You can proceed to next steps only when all items pass the pre-replacement check and the replacement page is displayed. If any item fails, rectify the fault as prompted.

  2. Wear an ESD wrist strap.
  3. Pull the spring pin upward, and press the adjustable guide rails of the cable manager to open the cable manager, as shown in Figure 6-152.

    Figure 6-152 Opening the cable manager

  4. Remove the power cable from the power module that you want to replace.

    1. Loosen the retention clip, as shown in step 1 in Figure 6-153.
      Figure 6-153 Removing the AC power cable

    2. Pull up the retention clip, as shown in a of step 2 in Figure 6-153.
    3. Remove the AC power cable, as shown in b of step 2 in Figure 6-153.

  5. Press the latch on the power module and pull out the power module, as shown in Figure 6-154.

    Figure 6-154 Removing a power module

  6. Put the removed power module into an ESD bag.
  7. Take the replacement power module out of its ESD bag.
  8. Insert the replacement power module into the slot until it clicks into place, as shown in Figure 6-155.

    Figure 6-155 Installing a power module

  9. Connect the power cable and fix the buckle of the power socket to the power cable.

    1. Press the locker of the retention clip outwards (as shown in a of step 1 in Figure 6-156), and meanwhile slide the retention clip to the connection part of the AC power cable (as shown in b of step 1 in Figure 6-156).
      Figure 6-156 Securing the AC power cables with retention clips

    2. Loosen the retention clip, as shown in step 2 in Figure 6-156.
    3. Press the retention clip inwards to secure the connection part of the AC power cable, as shown in step 3 in Figure 6-156
    NOTE:

    Adjust the retention clip to ensure that it holds the AC power cable tightly.

  10. Wait approximately two minutes and View the Running indicator of the power module to determine whether the power module is successfully installed. Figure 6-157 shows the location of the Running indicator on a power module.

    • If the indicator is steady green, the installation is successful.
    • If the indicator is off, the newly installed power module is faulty, the slot for the power module is faulty, or the power module is incorrectly installed.
    Figure 6-157 Running indicator on a power module

  11. Confirm the replacement.

    1. Perform a post-replacement inspection.

      After the parts replacement, return to the SmartKit page and click Replaced. Then complete the parts check after the replacement as prompted.

    2. Check system status.

      On the Parts Replacement page, click Inspection to check the system status again. If any inspection item fails, rectify the fault based on the suggestions.

    3. After the preceding procedure is complete, check services on the host for any storage-related error.

Follow-up Procedure

After the power module is replaced, label it to facilitate subsequent operations.

Translation
Download
Updated: 2019-07-11

Document ID: EDOC1000181634

Views: 46233

Downloads: 185

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next