No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Parts Replacement

OceanStor V5 Series V500R007

This document is applicable to OceanStor 5110 V5, 5110F V5, 5300 V5, 5300F V5, 5500 V5, 5500F V5, 5600 V5, 5600F V5, 5800 V5, 5800F V5, 6800 V5, 6800F V5, 18500 V5, 18500F V5, 18800 V5, and 18800F V5. This document describes the procedure for replacing the parts of storage system in terms of safety operations, preparations, and precautions.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Replacing an Expansion Module (Disk Enclosure)

Replacing an Expansion Module (Disk Enclosure)

This section describes how to replace an expansion module.

Impact on the System

During the replacement of an expansion module, the system switches services from ports on this module to ports on the other expansion module in the same disk enclosure. Only one expansion module is working, causing the system reliability to degrade. You are advised to replace an expansion module during off-peak hours.

Prerequisites

  • The spare part of the expansion module is ready.
  • The expansion module that you want to replace has been located.
NOTE:

You can locate a component in either of the following ways:

  • Log in to DeviceManager and go to the System page. On the System page, check the device view and locate the position of the component to be replaced. If the component has a location indicator, turn on the indicator. (For details about how to turn on a location indicator, see the online help of DeviceManager.)
  • Use the alarm indicator of the component to locate its position.
  • You have confirmed that the cables of the expansion module to be replaced are properly connected using Huawei Storage Product Networking Assistant (https://support.huawei.com/onlinetoolsweb/sna/#/home).
  • The cable connection positions of the expansion module are labeled on the cables.
  • The cables have been disconnected from the expansion module that you want to replace.
NOTE:

Before removing a SAS cable, gently push the connector of the cable inward. Then pull the plastic ring on the connector outward until the cable is completely removed from the expansion module.

Precautions

  • Remove and insert an expansion module with even force. Excessive force may damage the appearance or connectors of the expansion module.
  • An expansion module must be replaced within five minutes. Otherwise, the system heat dissipation is compromised.

Tools and Materials

  • ESD wrist strap
  • ESD bag
  • Label

Procedure

  1. Check status before replacement.

    1. Check system status.

      Start SmartKit and choose Home > Storage > Routine Maintenance > Health Check. On the Health Check page, perform inspection as instructed. For details, see Checking System Status.

      NOTE:

      If some items fail in the inspection, rectify the faults by performing the recommended actions in the inspection reports. Ensure that all other parts except the parts to be replaced are working properly.

    2. Check the status of the parts to be replaced.

      Start SmartKit and choose Home > Storage > Parts Replacement > Parts Replacement. On the Parts Replacement page, click FRU Replacement. Then complete the check before the replacement as prompted. For details, see Replacing an FRU.

    You can proceed to next steps only when all items pass the pre-replacement check and the replacement page is displayed. If any item fails, rectify the fault as prompted.

  2. Wear an ESD wrist strap.
  3. Press latches on the expansion module to release the handles and pull out the expansion module, as shown in Figure 6-190.

    Figure 6-190 Removing an expansion module

  4. Place the removed expansion module into an ESD bag.
  5. Take the replacement expansion module out of the ESD bag.
  6. Open the handles of the replacement expansion module, insert the expansion module into the empty slot, and close the handles, as shown in Figure 6-191.

    Figure 6-191 Installing an expansion module

  7. Connect the cables as labeled.
  8. Wait approximately two minutes and check the status of the Power and Alarm indicators on the expansion module to determine whether the expansion module is successfully installed. Figure 6-192 shows the locations of the Power and Alarm indicators.

    • If the Power indicator is steady on and the Alarm indicator is off, the expansion module is successfully installed.
    • If the Power indicator is off or the Alarm indicator is steady on, the newly installed expansion module is faulty, the expansion module slot is faulty, or the expansion module is incorrectly installed.
    Figure 6-192 Indicators on an expansion module

    1

    Alarm indicator of the expansion module

    2

    Power indicator of the expansion module

  9. Confirm the replacement.

    1. Perform a post-replacement inspection.

      After the parts replacement, return to the SmartKit page and click Replaced. Then complete the parts check after the replacement as prompted.

    2. Check system status.

      On the Parts Replacement page, click Inspection to check the system status again. If any inspection item fails, rectify the fault based on the suggestions.

    3. After the preceding procedure is complete, check services on the host for any storage-related error.

Follow-up Procedure

After the expansion module is replaced, label it to facilitate subsequent operations.

Translation
Download
Updated: 2019-07-11

Document ID: EDOC1000181634

Views: 46659

Downloads: 185

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next