No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionAccess Desktop Solution V100R006C20 Windows Desktop Management Guide 09 (FusionSphere V100R006C10 or Earlier)

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Creating a Template Using a User VM

Creating a Template Using a User VM

Scenarios

This section describes how to create a VM template using a user VM that has been provisioned to users.

Only the following types of templates can be created:

  • Create a full copy VM template using the VM provisioned by using a full copy VM template.
  • Create a QuickPrep VM template using the VM provisioned by using a QuickPrep VM template.
NOTE:

The following uses Windows 7 Professional 32-bit as an example.

Prerequisites

  • You have obtained the domain administrator account and its password.
  • An account with the local administrator permissions is available in the user VM.
  • You have logged in to FusionCompute.
  • You have logged in to the FusionAccess portal. For details, see Logging In to FusionAccess.
  • You have obtained the template tool FusionAccess_Windows_Installer_V100R006C20SPC102.iso.

Data

Data preparation is not required for this operation.

Procedure

Reset the password of the built-in administrator.

  1. Use the VNC to log in to the VM using the account with local administrator permissions.
  2. Click and choose Run. In the Run edit box, enter compmgmt.msc. The Computer Management window is displayed.
  3. In the navigation pane on the left, choose Computer Management(Local)> System Tools > Local Users and Group, and select Users.
  4. In the pane on the right, right-click Administrator (select a built-in administrator as required), choose Set Password For Administrator, and reset the password as prompted.
  5. Log out of the OS and log in to the VM as user Administrator (select a built-in administrator as required).

Delete a domain user.

  1. Click and choose Control Panel > User Accounts and Family Safety > User Accounts > Manage Accounts.
  2. Choose User Accounts > User, and delete all domain users.

Remove the VM from the domain.

  1. Determine whether a full clone template is to be created.

  2. Click and choose Run. In the Run edit box, enter sysdm.cpl. The System Properties window is displayed.
  3. On the Computer Name tab page, click Change. The Computer Name/Domain Changes dialog box is displayed.
  4. In the Member of area, select Workgroup and enter the name of the workgroup to be added, for example, WorkGroup.
  5. Click OK.

    The Computer Name/Domain Changes dialog box is displayed.

  6. Click OK.

    On the Computer Name/Domain Changes that is displayed, enter the username and password of the domain administrator.

  7. Click OK.

    The Welcome to the WorkGroup workgroup dialog box is displayed.

  8. Click OK.

    The You must restart your computer to apply these changes dialog box is displayed.

  9. Click OK.
  10. Close the System Properties window.
  11. On the dialog box that is displayed, click Restart now.
  12. Log in to the VM as user Administrator (select a built-in administrator as required).

Create a template.

  1. Mount the template tool FusionAccess_Windows_Installer_V100R006C20SPC102.iso to the VM.
  2. On the VM, double-click the CD/DVD-ROM drive.
  3. Double-click run.bat.

    NOTE:

    On some VMs, after you double-click the CD/DVD-ROM drive, the FusionAccess Windows Installer page is directly displayed.

  4. Click Create Template, as shown in Figure 4-1, and create a template as prompted.

    Figure 4-1 FusionAccess Windows Installer

Convert a VM into a template.

  1. Unmount the CD/DVD-ROM drive.
  2. Shut down the VM.
  3. On the FusionCompute portal, choose VM and Template > VM.
  4. In the row that contains the VM to be converted, choose More > Convert to Template.

    A dialog box is displayed.

  5. Click OK.

    A dialog box is displayed.

  6. Click OK.

(Optional) Change the template name.

  1. On the FusionCompute portal, choose VM and Template > VM, and click the template whose name you want to change.
  2. On the Summary tab page, click on the right of the template name.

    On the page for changing the tempalte name that is displayed, change the template name.

  3. Click OK in sequence.

Configure the template.

  1. On FusionAccess, choose Desktop.
  2. In the navigation pane on the left, choose Service Configuration > VM Template.
  3. In the pane on the right, locate the VM template to be provisioned and configure the following parameters as required:

    • Service type: Select a service type as required.
    • Type: Select a template type as required.

  4. Click OK.
  5. Click Confirm in the displayed dialog box.

    A message stating Template Configuration saved successfully is displayed.

  6. Click Back and check the template type.

    The template creation task is complete.

    NOTE:

    After being used to create a template, the VM cannot be used any more. However, the VM record can be queried in the FusionAccess Portal VM list. To delete the record, click Unassign next to the VM and click Delete.

Translation
Download
Updated: 2019-04-25

Document ID: EDOC1000182394

Views: 22013

Downloads: 59

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next