No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

WLAN V200R008C10 Typical Configuration Examples

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring the STA Blacklist and Whitelist

Example for Configuring the STA Blacklist and Whitelist

Service Requirements

An enterprise needs to provide WLAN services for management personnel so that they can connect to the enterprise network from anywhere at any time. Furthermore, users' services are not affected during roaming in the coverage area.

Due to a small number of management personnel in the enterprise, MAC addresses of their STAs can be added to a STA whitelist. In this manner, STAs of other employees cannot connect to the WLAN.

In addition, network administrators have detected unauthorized access of some STAs and need to deny access of them. The administrators can add MAC addresses of these STAs to the blacklist, while other authorized STAs can still connect to the WLAN.

Networking Requirements

  • AC networking mode: Layer 2 bypass mode
  • DHCP deployment mode:
    • The AC functions as a DHCP server to assign IP addresses to APs.
    • The aggregation switch (SwitchB) functions as a DHCP server to assign IP addresses to STAs.
  • Service data forwarding mode: tunnel forwarding
Figure 4-67 Networking for configuring the STA blacklist and whitelist

Data Planning

Table 4-68 AC data planning

Item

Data

Management VLAN for APs

VLAN 100

Service VLAN for STAs

VLAN 101

DHCP server

The AC functions as a DHCP server to assign IP addresses to APs.

SwitchB functions as a DHCP server to assign IP addresses to STAs. The default gateway address of STAs is 10.23.101.2.

IP address pool for APs 10.23.100.2-10.23.100.254/24
IP address pool for STAs 10.23.101.3-10.23.101.254/24
AC's source interface address VLANIF 100: 10.23.100.1/24
AP group
  • Name: ap-group1
  • Referenced profiles: VAP profile wlan-net, regulatory domain profile default, and AP system profile wlan-system
Regulatory domain profile
  • Name: default
  • Country code: China
SSID profile
  • Name: wlan-net
  • SSID name: wlan-net
Security profile
  • Name: wlan-net
  • Security policy: WPA-WPA2+PSK+AES
  • Password: a1234567
VAP profile
  • Name: wlan-net
  • Forwarding mode: tunnel forwarding
  • Service VLAN: VLAN 101
  • Referenced profiles: SSID profile wlan-net, security profile wlan-net, and STA whitelist profile sta-whitelist
STA whitelist profile
  • Name: sta-whitelist
  • STAs added to the STA whitelist: STA1 (0011-2233-4455) and STA2 (0011-2233-4466)
STA blacklist profile
  • Name: sta-blacklist
  • STAs added to the STA blacklist: STA3 (0011-2233-4477) and STA4 (0011-2233-4488)
AP system profile
  • Name: wlan-system
  • Referenced profile: STA blacklist profile sta-blacklist

Configuration Roadmap

  1. Configure basic WLAN services to ensure that users can access the WLAN.

  2. Configure a STA whitelist. Add MAC addresses of management personnel's wireless terminals to the whitelist. To prevent configuration impacts on other VAPs, configure the STA whitelist for a VAP, instead of an AP.
  3. Configure a STA blacklist for an AP. Add MAC addresses of some STAs to the blacklist to prevent the STAs from associating with the AP, ensuing WLAN network security.
NOTE:

The STA whitelist and blacklist cannot be configured simultaneously for a VAP or an AP, that is, the STA whitelist and blacklist cannot take effect at the same time in a VAP profile or an AP system profile.

Configuration Notes

  • No ACK mechanism is provided for multicast packet transmission on air interfaces. In addition, wireless links are unstable. To ensure stable transmission of multicast packets, they are usually sent at low rates. If a large number of such multicast packets are sent from the network side, the air interfaces may be congested. You are advised to configure multicast packet suppression to reduce impact of a large number of low-rate multicast packets on the wireless network. Exercise caution when configuring the rate limit; otherwise, the multicast services may be affected.
    • In direct forwarding mode, you are advised to configure multicast packet suppression on switch interfaces connected to APs.
    • In tunnel forwarding mode, you are advised to configure multicast packet suppression in traffic profiles of the AC.
    For details on how to configure traffic suppression, see How Do I Configure Multicast Packet Suppression to Reduce Impact of a Large Number of Low-Rate Multicast Packets on the Wireless Network?.
  • Configure port isolation on the interfaces of the device directly connected to APs. If port isolation is not configured and direct forwarding is used, a large number of unnecessary broadcast packets may be generated in the VLAN, blocking the network and degrading user experience.

  • In tunnel forwarding mode, the management VLAN and service VLAN cannot be the same. Only packets from the management VLAN are transmitted between the AC and APs. Packets from the service VLAN are not allowed between the AC and APs.

Procedure

  1. Configure the network devices.

    # Add GE0/0/1 and GE0/0/2 on SwitchA to VLAN 100. The default VLAN of GE0/0/1 is VLAN 100.
    <HUAWEI> system-view
    [HUAWEI] sysname SwitchA
    [SwitchA] vlan batch 100
    [SwitchA] interface gigabitethernet 0/0/1
    [SwitchA-GigabitEthernet0/0/1] port link-type trunk
    [SwitchA-GigabitEthernet0/0/1] port trunk pvid vlan 100
    [SwitchA-GigabitEthernet0/0/1] port trunk allow-pass vlan 100
    [SwitchA-GigabitEthernet0/0/1] port-isolate enable
    [SwitchA-GigabitEthernet0/0/1] quit
    [SwitchA] interface gigabitethernet 0/0/2
    [SwitchA-GigabitEthernet0/0/2] port link-type trunk
    [SwitchA-GigabitEthernet0/0/2] port trunk allow-pass vlan 100
    [SwitchA-GigabitEthernet0/0/2] quit
    
    # Add GE0/0/1 and GE0/0/2 on SwitchB (aggregation switch) to VLAN 100, and GE0/0/2 and GE0/0/3 to VLAN 101.
    <HUAWEI> system-view
    [HUAWEI] sysname SwitchB
    [SwitchB] vlan batch 100 101
    [SwitchB] interface gigabitethernet 0/0/1
    [SwitchB-GigabitEthernet0/0/1] port link-type trunk
    [SwitchB-GigabitEthernet0/0/1] port trunk allow-pass vlan 100
    [SwitchB-GigabitEthernet0/0/1] quit
    [SwitchB] interface gigabitethernet 0/0/2
    [SwitchB-GigabitEthernet0/0/2] port link-type trunk
    [SwitchB-GigabitEthernet0/0/2] port trunk allow-pass vlan 100 101
    [SwitchB-GigabitEthernet0/0/2] quit
    [SwitchB] interface gigabitethernet 0/0/3
    [SwitchB-GigabitEthernet0/0/3] port link-type trunk
    [SwitchB-GigabitEthernet0/0/3] port trunk allow-pass vlan 101
    [SwitchB-GigabitEthernet0/0/3] quit
    
    # Add GE1/0/0 on Router to VLAN 101. Create VLANIF 101 and set its IP address to 10.23.101.2/24.
    <Huawei> system-view
    [Huawei] sysname Router
    [Router] vlan batch 101
    [Router] interface gigabitethernet 1/0/0
    [Router-GigabitEthernet1/0/0] port link-type trunk
    [Router-GigabitEthernet1/0/0] port trunk allow-pass vlan 101
    [Router-GigabitEthernet1/0/0] quit
    [Router] interface vlanif 101
    [Router-Vlanif101] ip address 10.23.101.2 24
    [Router-Vlanif101] quit
    

  2. Configure the AC to communicate with the network devices.

    NOTE:

    If the AC and APs are directly connected, set the default VLAN of the interfaces connected to the APs to management VLAN 100.

    # Add GE0/0/1 on the AC to VLAN 100 and VLAN 101.
    <AC6605> system-view
    [AC6605] sysname AC
    [AC] vlan batch 100 101
    [AC] interface gigabitethernet 0/0/1
    [AC-GigabitEthernet0/0/1] port link-type trunk
    [AC-GigabitEthernet0/0/1] port trunk allow-pass vlan 100 101
    [AC-GigabitEthernet0/0/1] quit
    

  3. Configure the DHCP servers to assign IP addresses to APs and STAs.

    # On the AC, configure VLANIF 100 to assign IP addresses to APs.
    [AC] dhcp enable
    [AC] interface vlanif 100
    [AC-Vlanif100] ip address 10.23.100.1 24
    [AC-Vlanif100] dhcp select interface
    [AC-Vlanif100] quit
    
    # On SwitchB, configure VLANIF 101 to assign IP addresses to STAs and set the default gateway address of STAs to 10.23.101.2.
    NOTE:
    Configure the DNS server as required. The common methods are as follows:
    • In interface address pool scenarios, run the dhcp server dns-list ip-address &<1-8> command in the VLANIF interface view.
    • In global address pool scenarios, run the dns-list ip-address &<1-8> command in the IP address pool view.
    [SwitchB] dhcp enable
    [SwitchB] interface vlanif 101
    [SwitchB-Vlanif101] ip address 10.23.101.1 24
    [SwitchB-Vlanif101] dhcp select interface
    [SwitchB-Vlanif101] dhcp server gateway-list 10.23.101.2
    [SwitchB-Vlanif101] quit
    

  4. Configure an AP to go online.

    # Create an AP group to which the APs with the same configuration can be added.
    [AC] wlan
    [AC-wlan-view] ap-group name ap-group1
    [AC-wlan-ap-group-ap-group1] quit
    
    # Create a regulatory domain profile, configure the AC country code in the profile, and apply the profile to the AP group.
    [AC-wlan-view] regulatory-domain-profile name default
    [AC-wlan-regulate-domain-default] country-code cn
    [AC-wlan-regulate-domain-default] quit
    [AC-wlan-view] ap-group name ap-group1
    [AC-wlan-ap-group-ap-group1] regulatory-domain-profile default
    Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continu
    e?[Y/N]:y 
    [AC-wlan-ap-group-ap-group1] quit
    [AC-wlan-view] quit
    
    # Configure the AC's source interface.
    [AC] capwap source interface vlanif 100
    
    # Import the AP offline on the AC and add the AP to AP group ap-group1. Assume that the AP's MAC address is 60de-4476-e360. Configure a name for the AP based on the AP's deployment location, so that you can know where the AP is deployed from its name. For example, name the AP area_1 if it is deployed in Area 1.
    NOTE:

    The default AP authentication mode is MAC address authentication. If the default settings are retained, you do not need to run the ap auth-mode mac-auth command.

    In this example, the AP5030DN is used and has two radios: radio 0 (2.4 GHz radio) and radio 1 (5 GHz radio).

    [AC] wlan
    [AC-wlan-view] ap auth-mode mac-auth
    [AC-wlan-view] ap-id 0 ap-mac 60de-4476-e360
    [AC-wlan-ap-0] ap-name area_1
    Warning: This operation may cause AP reset. Continue? [Y/N]:y 
    [AC-wlan-ap-0] ap-group ap-group1
    Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration
    s of the radio, Whether to continue? [Y/N]:y 
    [AC-wlan-ap-0] quit
    
    # After the AP is powered on, run the display ap all command to check the AP state. If the State field is displayed as nor, the AP goes online successfully.
    [AC-wlan-view] display ap all
    Total AP information:
    nor  : normal          [1]
    Extra information:
    P  : insufficient power supply
    --------------------------------------------------------------------------------------------------
    ID   MAC            Name   Group     IP            Type            State STA Uptime      ExtraInfo
    --------------------------------------------------------------------------------------------------
    0    60de-4476-e360 area_1 ap-group1 10.23.100.254 AP5030DN        nor   0   10S         -
    --------------------------------------------------------------------------------------------------
    Total: 1

  5. Configure WLAN service parameters.

    # Create security profile wlan-net and set the security policy in the profile.
    NOTE:

    In this example, the security policy is set to WPA-WPA2+PSK+AES and password to a1234567. In actual situations, the security policy must be configured according to service requirements.

    [AC-wlan-view] security-profile name wlan-net
    [AC-wlan-sec-prof-wlan-net] security wpa-wpa2 psk pass-phrase a1234567 aes
    [AC-wlan-sec-prof-wlan-net] quit
    
    # Create SSID profile wlan-net and set the SSID name to wlan-net.
    [AC-wlan-view] ssid-profile name wlan-net
    [AC-wlan-ssid-prof-wlan-net] ssid wlan-net
    [AC-wlan-ssid-prof-wlan-net] quit
    
    # Create VAP profile wlan-net, set the data forwarding mode and service VLAN, and apply the security profile and SSID profile to the VAP profile.
    [AC-wlan-view] vap-profile name wlan-net
    [AC-wlan-vap-prof-wlan-net] forward-mode tunnel
    [AC-wlan-vap-prof-wlan-net] service-vlan vlan-id 101
    [AC-wlan-vap-prof-wlan-net] security-profile wlan-net
    [AC-wlan-vap-prof-wlan-net] ssid-profile wlan-net
    [AC-wlan-vap-prof-wlan-net] quit
    
    # Bind VAP profile wlan-net to the AP group and apply the profile to radio 0 and radio 1 of the AP.
    [AC-wlan-view] ap-group name ap-group1
    [AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 0
    [AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 1
    [AC-wlan-ap-group-ap-group1] quit
    

  6. Configure the AP channel and power.

    NOTE:

    Automatic channel and power calibration functions are enabled by default. The manual channel and power configurations take effect only when these two functions are disabled. The settings of the AP channel and power in this example are for reference only. You need to configure the AP channel and power based on the actual country code and network planning.

    # Disable automatic channel and power calibration functions of radio 0, and configure the channel and power for radio 0.
    [AC-wlan-view] ap-id 0
    [AC-wlan-ap-0] radio 0
    [AC-wlan-radio-0/0] calibrate auto-channel-select disable
    [AC-wlan-radio-0/0] calibrate auto-txpower-select disable
    [AC-wlan-radio-0/0] channel 20mhz 6
    Warning: This action may cause service interruption. Continue?[Y/N]y
    [AC-wlan-radio-0/0] eirp 127
    [AC-wlan-radio-0/0] quit
    # Disable automatic channel and power calibration functions of radio 1, and configure the channel and power for radio 1.
    [AC-wlan-ap-0] radio 1
    [AC-wlan-radio-0/1] calibrate auto-channel-select disable
    [AC-wlan-radio-0/1] calibrate auto-txpower-select disable
    [AC-wlan-radio-0/1] channel 20mhz 149
    Warning: This action may cause service interruption. Continue?[Y/N]y
    [AC-wlan-radio-0/1] eirp 127
    [AC-wlan-radio-0/1] quit
    [AC-wlan-ap-0] quit

  7. Configure a STA whitelist in a VAP profile.

    # Create STA whitelist profile sta-whitelist and add MAC addresses of STA1 and STA2 to the whitelist.

    [AC-wlan-view] sta-whitelist-profile name sta-whitelist
    [AC-wlan-whitelist-prof-sta-whitelist] sta-mac 0011-2233-4455
    [AC-wlan-whitelist-prof-sta-whitelist] sta-mac 0011-2233-4466
    [AC-wlan-whitelist-prof-sta-whitelist] quit

    # Create the VAP profile wlan-net and bind the STA whitelist profile to the VAP profile.

    [AC-wlan-view] vap-profile name wlan-net
    [AC-wlan-vap-prof-wlan-net] sta-access-mode whitelist sta-whitelist
    [AC-wlan-vap-prof-wlan-net] quit
    

  8. Configure a global STA blacklist.

    # Create STA blacklist profile sta-blacklist and add MAC addresses of STA3 and STA4 to the blacklist.

    [AC-wlan-view] sta-blacklist-profile name sta-blacklist
    [AC-wlan-blacklist-prof-sta-blacklist] sta-mac 0011-2233-4477
    [AC-wlan-blacklist-prof-sta-blacklist] sta-mac 0011-2233-4488
    [AC-wlan-blacklist-prof-sta-blacklist] quit

    # Create the AP system profile wlan-system and bind the STA blacklist profile to the AP system profile.

    [AC-wlan-view] ap-system-profile name wlan-system
    [AC-wlan-ap-system-prof-wlan-system] sta-access-mode blacklist sta-blacklist
    [AC-wlan-ap-system-prof-wlan-system] quit
    

    # Bind AP system profile wlan-system to AP group ap-group1.

    [AC-wlan-view] ap-group name ap-group1
    [AC-wlan-ap-group-ap-group1] ap-system-profile wlan-system
    [AC-wlan-ap-group-ap-group1] quit
    

  9. Verify the configuration.

    The WLAN with SSID wlan-net is available for STAs connected to the AP.

    STA1 and STA2 can connect to the WLAN. STA3 and STA4 cannot connect to the WLAN.

Configuration Files

  • SwitchA configuration file

    #
    sysname SwitchA
    #
    vlan batch 100
    #
    interface GigabitEthernet0/0/1
     port link-type trunk
     port trunk pvid vlan 100
     port trunk allow-pass vlan 100
     port-isolate enable group 1
    #
    interface GigabitEthernet0/0/2
     port link-type trunk
     port trunk allow-pass vlan 100
    #
    return
  • SwitchB configuration file

    #
    sysname SwitchB
    #
    vlan batch 100 to 101
    #
    dhcp enable
    #
    interface Vlanif101
     ip address 10.23.101.1 255.255.255.0
     dhcp select interface
     dhcp server gateway-list 10.23.101.2
    #
    interface GigabitEthernet0/0/1
     port link-type trunk
     port trunk allow-pass vlan 100
    #
    interface GigabitEthernet0/0/2
     port link-type trunk
     port trunk allow-pass vlan 100 to 101
    #
    interface GigabitEthernet0/0/3
     port link-type trunk
     port trunk allow-pass vlan 101
    #
    return
  • Router configuration file

    #
    sysname Router
    #
    vlan batch 101
    #
    interface Vlanif101
     ip address 10.23.101.2 255.255.255.0
    #
    interface GigabitEthernet1/0/0
     port link-type trunk
     port trunk allow-pass vlan 101
    #
    return
    
  • AC configuration file

    #
     sysname AC
    #
    vlan batch 100 to 101
    #
    dhcp enable
    #
    interface Vlanif100
     ip address 10.23.100.1 255.255.255.0
     dhcp select interface
    #
    interface GigabitEthernet0/0/1
     port link-type trunk
     port trunk allow-pass vlan 100 101
    #
    capwap source interface vlanif100
    #
    wlan
      security-profile name wlan-net
      security wpa-wpa2 psk pass-phrase %^%#m"tz0f>~7.[`^6RWdzwCy16hJj/Mc!,}s`X*B]}A%^%# aes
     sta-blacklist-profile name sta-blacklist
      sta-mac 0011-2233-4477
      sta-mac 0011-2233-4488
     sta-whitelist-profile name sta-whitelist
      sta-mac 0011-2233-4455
      sta-mac 0011-2233-4466
     ssid-profile name wlan-net
      ssid wlan-net
     vap-profile name wlan-net
      forward-mode tunnel
      service-vlan vlan-id 101
      sta-access-mode whitelist sta-whitelist
      ssid-profile wlan-net
      security-profile wlan-net
     regulatory-domain-profile name default
     ap-system-profile name wlan-system
      sta-access-mode blacklist sta-blacklist
     ap-group name ap-group1
      ap-system-profile wlan-system
      radio 0
       vap-profile wlan-net wlan 1
      radio 1
       vap-profile wlan-net wlan 1
     ap-id 0 type-id 35 ap-mac 60de-4476-e360 ap-sn 210235554710CB000042
      ap-name area_1
      ap-group ap-group1
      radio 0
       channel 20mhz 6
       eirp 127
       calibrate auto-channel-select disable
       calibrate auto-txpower-select disable
      radio 1
       channel 20mhz 149
       eirp 127
       calibrate auto-channel-select disable
       calibrate auto-txpower-select disable
    #
    return
Translation
Download
Updated: 2019-03-30

Document ID: EDOC1000184389

Views: 91186

Downloads: 460

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next