No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

WLAN V200R008C10 Typical Configuration Examples

Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring the Device as a PPPoE Client

Example for Configuring the Device as a PPPoE Client

Networking Requirements

As shown in Figure 5-13, the device functioning as the PPPoE client connects to the PPPoE server using GE0/0/0.

Users want the hosts to share an account. If the account is authenticated successfully on the PPPoE server, a PPPoE session is established. Service requirements are as follows:

  • The device establishes a PPPoE session with the PPPoE server using PPP authentication.

  • The device automatically attempts to create a dial-up connection again at intervals after the disconnection.
Figure 5-13 Networking diagram of the device functioning as the PPPoE client

Data Planning

Table 5-13 AC data planning

Item

Data

Uplink port

GE0/0/0

IP address allocation mode

PPPoE dialup

User name/Password

user1@system/huawei123

VLAN to which the PPPoE session is bound.

VLAN 100

NAT

Enabled

Configuration Roadmap

The configuration roadmap is as follows:
  1. Configure the PPPoE server.
  2. Configure the PPPoE client. Use the configuration wizard to configure the PPPoE dialup function on the AP and enable NAT to translate private IP addresses to public IP addresses.

Procedure

  1. Configure the PPPoE server.

    # Configure the authentication mode, IP address allocation mode, and IP address or IP address pool for PPPoE clients. For details about the configuration procedure, see the documentation of the PPPoE server.

  2. Configure the PPPoE client.
    1. Create VLAN 100 and add GE0/0/0 to VLAN 100.

      # Choose Configuration > Central AP Config > VLAN > VLAN. The VLAN page is displayed.

      # Click Create. On the Create VLAN page that is displayed, set VLAN ID to 100. Select GigabitEthernet0/0/0 in Available Interface List and click . In the Modify Link Type dialog box that is displayed, set Link type to Trunk and Mode to Tagged.



      # Click OK.

    2. Add GE0/0/0 to the default VLAN 100.

      # Choose Configuration > Central AP Config > Interface > Interface Attribute. The Interface Attribute page is displayed.

      # Click GigabitEthernet0/0/0. On the Modify Interface Settings page that is displayed, set Default VLAN to 100.



      # Click OK.

    3. Create VLANIF 100 and configure the PPPoE client.

      # Choose Configuration > Central AP Config > VLAN > VLANIF. The VLANIF page is displayed.

      # Click Create. On the Create VLANIF page that is displayed, set VLAN ID to 100, Connection type to Broadband dialup, User name to user1@system, Password to huawei123, and Enable NAT to ON.



      # Click OK.

  3. Verify the configuration.

    After the configuration is complete, a PPPoE dialup interface is automatically generated, through which hosts on the LAN can connect to the Internet using dialup. When wireless users attempt to connect to the public network, private IP addresses are translated into public IP addresses for communication.

Translation
Download
Updated: 2019-03-30

Document ID: EDOC1000184389

Views: 90396

Downloads: 458

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next