No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Maintenance Guide

TE30, TE40, TE50, TE60, and TX50 Videoconferencing Endpoint V600R006C10

This document guides the operator to maintain the device
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adding Sites Using the Remote Control

Adding Sites Using the Remote Control

After adding some sites to the address book, you will see them in the Call window.

  1. Press on the remote control to access the menu screen.
  2. Choose Advanced > Address Book from the option bar.
  3. If no site is displayed, select Add Site. If some sites exist, select next to any site, and press on the remote control.
  4. In Create Site, name the site you wish to add.

    The value can contain digits, letters, and special characters, such as @ # %.

  5. Set the site parameters by referring to Table 3-1.

    Table 3-1 Site parameters

    Parameter

    Description

    Setting

    Set favorite venue

    If a site is set as a favorite site, the site will be pinned on the top of the address book.

    The default value is No.

    Category

    Specifies the site type.

    • Ordinary site: Select this option for a traditional videoconferencing site.
    • Telepresence site: Select this option for a Huawei tri-screen telepresence site.
    • CT site: Select this option for a Cisco TelePresence site.

    The default value is Ordinary site.

    Type

    Specifies the type of the line the site uses to access the videoconferencing network.
    • If you select IP, your endpoint will use the protocol set for Preferred IP protocol to call the site.
    • If you set Category to CT site, the available value for Type is SIP.

    The default value is H.323.

    Rate

    Specifies the data transmission rate of the line selected for the remote endpoint.

    The supported data transmission rates vary depending on the type of the site you want to call.

    Select the highest available data transmission rate.

    Country/Region code

    Specifies the country or area where the site is located.

    This parameter is available only for integrated services digital network (ISDN) and public switched telephone network (PSTN) sites.

    No default value is set for this parameter.

    Area code

    Specifies the area code for the site.

    This parameter is available only for ISDN and PSTN sites.

    No default value is set for this parameter.

    Number

    Specifies the site number used to place calls between sites.
    • IP, E1, 4E1, ISDN, and H.323 phone site numbers are allocated by the videoconferencing service provider.
    • PSTN site numbers are telephone numbers.

    No default value is set for this parameter.

    IP address

    Specifies the IP address of the site.

    NOTE:

    This parameter is unavailable if you set Category to CT site.

    No default value is set for this parameter.

    URI

    Specifies the uniform resource identifier (URI) of the site, for example, abcd@huawei.com.

    NOTE:

    This parameter is available only when Type is set to IP, H.323, or SIP.

    No default value is set for this parameter.

    Line 1 #1

    Line 1 #2

    Line 2 #1

    Line 2 #2

    Line 3 #1

    Line 3 #2

    Specify the numbers your endpoint uses to call the site. These parameters are available only for ISDN sites.

    • If the ISDN site rate is set to a value ranging from 64 kbit/s to 2048 kbit/s, set Line 1 #1 only, because you only need to dial that number to call the site.
    • If the ISDN site rate is set to 2, 3, 4, 5, or 6 x 64 kbit/s, set the other required parameters as well, because you need to dial the BRI line numbers one by one to call the site. For example, when the ISDN site rate is set to 2 x 64 kbit/s, set the first two parameters Line 1 #1 and Line 1 #2; when the ISDN site rate is set to 3 x 64 kbit/s, set the first three parameters Line 1 #1, Line 1 #2, and Line 2 #1, and so forth. Line 1 #2 specifies the second number of the first BRI line.

    No default value is set for this parameter.

  6. Select Save and press on the remote control.

    The settings take effect immediately. The new site is listed in the address book.

Translation
Download
Updated: 2019-01-31

Document ID: EDOC1000184611

Views: 32725

Downloads: 164

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next