No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OceanStor 9000 V300R006C20 Hardware Installation Guide 05

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Connecting a Signal Cable for a P25E/P36E/P12E/C36E Node (Front-End 10GE Network + Back-End IB Network)

Connecting a Signal Cable for a P25E/P36E/P12E/C36E Node (Front-End 10GE Network + Back-End IB Network)

When 10GE switches are used on the front-end network and IB switches are used on the back-end network on OceanStor 9000, connect storage nodes to switches using signal cables.

Prerequisites

  • Information about the current network and associated ports has been obtained.
  • Required components have been installed in the cabinet.
  • PGND cables and power cables have been connected to the components in the cabinet.
  • All required tools have been prepared, containing cable ties, diagonal pliers, and ESD gloves or an ESD wrist strap.

Storage Node Port Planning

When the front-end network uses 10GE network and the back-end network uses IB network of OceanStor 9000, ports on storage nodes are shown in Figure 10-54 and their usage is described in Table 10-26.

Figure 10-54  Storage node ports (front-end 10GE network + back-end IB network)
Table 10-26  Usage of storage node ports (front-end 10GE network + back-end IB network)

Port

Type

Access Network

Description

SLOT4-0 and SLOT4-1

40GE QSFP+ Ethernet optical port

Back-end network

The nodes connect to the two SX6018 IB switches through FDR cables.

SLOT5-0 and SLOT5-1

10GE SFP+ Ethernet optical port

Front-end network

Connects to the 10GE switches on the user's network using optical fibers.

NIC1

GE electrical port

Management and maintenance network

Connects each NIC1 port on the bottom three nodes to the GE switch in the basic cabinet using network cables.

Mgmt

FE electrical port

Management and maintenance network

Connects to the GE switches in the basic cabinet using network cables.

Switch Port Planning

Ports on an SX6018 IB switch in a cabinet are shown in Figure 10-55, and their usage is described in Table 10-27.
Figure 10-55  SX6018 IB switch ports

Table 10-27  Usage of SX6018 IB switch ports

Port

Type

Access Network

Description

1 to 16

QSFP + port

Back-end network

Each SX6018 switch connects to nodes using 16 ports in sequence.

  • Switch SX6018-01 connects to SLOT4-0 on each storage node.
  • Switch SX6018-02 connects to SLOT4-1 on each storage node.

17 and 18

QSFP + port

-

Connects two SX6018 switches.

In the basic cabinet, the S5752/S5352/CE5855 GE switch ports for connecting to the management and maintenance network are shown in Figure 10-56 and Figure 10-57, and the port usage is described in Table 10-22.
Figure 10-56   S5752/S5352 GE switch ports

Figure 10-57  CE5855 GE switch ports

Procedure

  1. Wear an ESD wrist strap or ESD gloves.
  2. Determine port numbers of the storage node and signal cable connection modes.
  3. Obtain the required types of cables and label them.
  4. Optional: Install an optical module.

    • Wear an ESD wrist strap or gloves to prevent damaging ESD-sensitive optical modules.
    • Do not insert an optical module reversely. If an optical module cannot be completely inserted into an optical module slot, do not force it into the slot. Turn the optical module over and try again.
    • Do not remove dust-proof caps from optical connectors before connecting optical fibers to optical modules.
    • Optical modules and optical fibers support only multi-mode optical modules.

    1. Take out an optical module from an ESD bag and verify that the optical module is intact.
    2. Insert the optical module into an optical port on the subcard until it snaps into place and then raise the handle to lock it up, as shown in Figure 10-58.

      When the locking reed of the optical module makes a "click" sound, the optical module is installed correctly.

      Figure 10-58  Installing an optical module

  5. Connect cables according to the attached label.

    • To connect a copper cable, hold a copper cable connector in a correct direction when inserting it into a port. When you hear a click, the copper cable is securely connected to the port.
    • To remove a copper cable, gently push the cable connector and then pull the handle of the connector. Do not directly pull the cable connector with force, as shown in Figure 10-59.
      Figure 10-59   Removing a copper cable

    • After connecting cables to the devices, reserve adequate cable slack for ease of operation on other FRUs.

  6. Lay out the cables along the mounting bars neatly, use cable ties to bind them, and trim off the excess of cable ties using diagonal pliers.

Example

In the example shown in Figure 10-60, 10GE switches are used on the front-end network and IB switches are used on the back-end network, and three P25E nodes are deployed.

Figure 10-60  Cabling of a three-P25E cluster (IB network)

NOTE:

The nodes connect to the two SX6018 IB switches through FDR cables.

Translation
Download
Updated: 2019-03-26

Document ID: EDOC1000185366

Views: 43470

Downloads: 162

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next