No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

CloudEngine 8800, 7800, 6800, and 5800 V200R003C00

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, MUX VLAN, Voice VLAN, VLAN mapping, QinQ, GVRP, VCMP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, and Layer 2 protocol transparent transmission.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Terms and Abbreviations

Terms and Abbreviations

Terms

Term

Description

10Base-T

Defined in IEEE 802.3i, it is an Ethernet specification that uses the twist pair with the maximum length of 100 meters (328.08 ft.) at 10 Mbit/s for each network segment.

100Base-T

Defined in IEEE 802.3u, it is a Fast Ethernet specification that uses the twist pair with the maximum length of 100 meters (328.08 ft.) at 100 Mbit/s for each network segment.

1000BaseT

Defined in IEEE 802.3ab, it is an Ethernet specification that uses the twist pair with the maximum length of 100 meters (328.08 ft.) at 1000 Mbit/s for each network segment.

Ethernet

Created by Xerox and developed by Xerox, Intel, and Digital Equipment Corporation (DEC), it is a baseband LAN specification that uses CSMA/CD and transmits data over various cables at 10 Mbit/s. Ethernet-related standards are defined in IEEE 802.3 series.

Ethernet_II

An encapsulation format of Ethernet frames, which is the standard ARPA Ethernet Version 2.0 encapsulation that uses a 16-bit protocol type code.

Ethernet_SNAP

An encapsulation format of Ethernet frames. As specified in RFC 1042, it allows Ethernet frames to be transmitted through IEEE 802.2 media.

FE

Short for the Fast Ethernet. Complying with IEEE 802.3u, it is an extension and enhancement of the traditional media-sharing Ethernet standard and allows data to be transmitted at 100 Mbit/s.

Full-duplex

The full-duplex mode is an operation mode of Ethernet interfaces. In full-duplex mode, interfaces on both ends can send and receive data at the same time without interruption.

GE

Short for Gigabit Ethernet. Complying with IEEE 802.3z, the GE is compatible with the 10M Ethernet and the 100M Ethernet (FE).

Half-duplex

An operation mode of Ethernet interfaces. In half-duplex mode, an interface can only receive or send data at a time.

MAC

Short for Media Access Control. At the data link layer of the OSI model, the MAC sub-layer is adjacent to the physical layer.

Auto-negotiation

A function that enables devices on both ends of a physical link to automatically select an operation mode by exchanging information. In auto-negotiation, the duplex mode and operation rate are negotiated. Once the negotiation result is approved, the operation mode is fixed until the device is restarted or the cable is removed.

Abbreviations

Abbreviation

Full Name

CSMA/CD

Carrier Sense Multiple Access with Collision Detection

GE

Gigabit Ethernet

MAC

Media Access Control

TCP

Transmission Control Protocol

Translation
Download
Updated: 2019-05-08

Document ID: EDOC1100004351

Views: 82094

Downloads: 274

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next