No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

CloudEngine 8800, 7800, 6800, and 5800 V200R003C00

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, MUX VLAN, Voice VLAN, VLAN mapping, QinQ, GVRP, VCMP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring Loopback Detection

Example for Configuring Loopback Detection

Networking Requirements

As shown in Figure 13-3, if there is a loop on the network connected to the 10GE1/0/1 interface, broadcast storms will occur on the Switch or even the entire network.

To detect loops on the network connected to the switch and disabled downlink interfaces to reduce impacts on the switch and other networks, enable loopback detection on the Switch.

Figure 13-3 Loopback detection network diagram

Configuration Roadmap

The configuration roadmap is as follows:

  1. Enable loopback detection on the interface to detect loops on downlink networks.
  2. Specify the VLAN ID for loopback detection packets.
  3. Set loopback detection parameters to enable the interface automatic recovery.

Procedure

  1. Enable loopback detection on the interface.

    <HUAWEI> system-view
    [~HUAWEI] sysname Switch
    [*HUAWEI] commit
    [~Switch] interface 10ge 1/0/1
    [~Switch-10GE1/0/1] loopback-detect enable
    [*Switch-10GE1/0/1] commit
    [~Switch-10GE1/0/1] quit

  2. Specify the VLAN ID for loopback detection packets.

    [~Switch] vlan 100
    [*Switch-vlan100] quit
    [*Switch] interface 10ge 1/0/1
    [*Switch-10GE1/0/1] port link-type trunk
    [*Switch-10GE1/0/1] port trunk allow-pass vlan 100
    [*Switch-10GE1/0/1] loopback-detect vlan 100
    [*Switch-10GE1/0/1] commit
    [~Switch-10GE1/0/1] quit

  3. Set loopback detection parameters.

    # Configure the action the interface when a loopback is detected.

    [~Switch] loopback-detect action error-down
    [*Switch] commit

    # Set the interval between sending loopback detection packets.

    [~Switch] loopback-detect transmit interval 10
    [*Switch] commit

  4. Check the configuration.

    Run the display loopback-detect command to check the configuration.

    [~Switch] display loopback-detect 
    ------------------------------------------------------------                                                                        
     Loopback-detect transmit interval: 10s                                                                                             
    ------------------------------------------------------------                                                                        
    ------------------------------------------------------------                                                                        
    Interface                Action                   Status                                                                            
    ------------------------------------------------------------                                                                        
    10GE1/0/1                Error-Down               ErrorDown

Configuration Files

Configuration file of the Switch

#
sysname Switch
#
loopback-detect transmit interval 10
loopback-detect action error-down
#
vlan batch 100
#
interface 10GE1/0/1
 port link-type trunk
 port trunk allow-pass vlan 100
 loopback-detect enable
 loopback-detect vlan 100
#
return
Translation
Download
Updated: 2019-05-08

Document ID: EDOC1100004351

Views: 126062

Downloads: 295

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next