No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

CloudEngine 8800, 7800, 6800, and 5800 V200R003C00

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, MUX VLAN, Voice VLAN, VLAN mapping, QinQ, GVRP, VCMP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, and Layer 2 protocol transparent transmission.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Binding an Eth-Trunk Member Interface to a VLAN

(Optional) Binding an Eth-Trunk Member Interface to a VLAN

Context

A server is often equipped with two or more network adapters. When a server connects to a switch, one network adapter is used for server management and the other network adapters are used for traffic forwarding. In this case, there is much idle time on the network adapter used for server management and switch interfaces, and the bandwidth use efficiency is low. To address this issue, upgrade the server software so that the network adapter used for server management can be also used for traffic forwarding. When the switch uses an Eth-Trunk to connect to the server, one Eth-Trunk member interface can be bound to a VLAN for server management. In addition, service VLANs can be configured on the Eth-Trunk so that service traffic is load balanced among all Eth-Trunk member interfaces. The bandwidth use efficiency is therefore improved.

NOTE:

The CE6870EI and CE6875EI do not support this function.

NOTE:
  • This function applies to the scenario where a switch connects to a server, and it can only be configured on the member interface connecting to the server's management NIC.
  • In an Eth-Trunk, only one member interface can be bound to a VLAN or VLANs and one member interface can be bound to a maximum of eight VLANs. Member interfaces of multiple Eth-Trunks can be bound to the same VLAN.
  • The switch supports a maximum of 256 bound VLANs. If N Eth-Trunk member interfaces are bound to M VLANs, the maximum value of N multiplied by M is 256.
  • After this command is configured, packets from the bound VLAN can be only forwarded through the bound Eth-Trunk member interface. Non-unicast traffic on the Eth-Trunk can be only forwarded through the bound Eth-Trunk member interface.
  • When an Eth-Trunk member interface is bound to a VLAN or VLANs, VLAN mapping, VLAN stacking, MUX VLAN, or FCoE VLAN cannot be configured.
  • When an Eth-Trunk member interface is bound to a VLAN or VLANs, M-LAG cannot be configured.
  • If Layer 2 sub-interfaces are created on an Eth-Trunk and a member interface is bound to an independent VLAN, the VLAN cannot connect to non-VXLAN tunnels.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The Eth-Trunk member interface view is displayed.

  3. Run trunk member binding vlan vlan-id

    The Eth-Trunk member interface is bound to a VLAN.

    By default, an Eth-Trunk member interface is not bound to a VLAN.

  4. Run commit

    The configuration is committed.

Translation
Download
Updated: 2019-05-08

Document ID: EDOC1100004351

Views: 97330

Downloads: 276

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next