No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionAccess V100R006C20 Alarm Handling 05 (FusionSphere 6.3.1)

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
1000012 FusionCompute Server Abnormal

1000012 FusionCompute Server Abnormal

Description

The alarm module checks the FusionCompute server every 2 minutes. This alarm is generated when the alarm module detects that the FusionCompute server is abnormal or unavailable for three consecutive times. This alarm is cleared when the alarm module detects that the FusionCompute server becomes normal.

Attribute

Alarm ID

Alarm Severity

Auto Clear

1000012

Critical

Yes

Parameters

Name

Meaning

Alarm ID

Identifies an alarm. Each alarm is uniquely identified by an alarm ID and an alarm name.

Alarm Severity

Indicates the severity of an alarm. Value:

  • Critical: indicates that a fault affecting services provided by the system occurs. You need to rectify the fault immediately. If a device or resource is faulty, rectify it immediately even if the fault occurs during non-working hours.
  • Major: indicates that a fault affecting the service quality of the system occurs. You need to rectify the fault immediately. If the service quality of a device or resource is degraded, rectify it immediately during working hours.
  • Minor: indicates a fault that does not affect service quality. To prevent more serious faults, this type of alarm needs to be observed or handled if necessary.
  • Warning: indicates a fault that may affect service quality. This type of alarm must be handled based on the error type.

Alarm Name

Identifies an alarm. Each alarm is uniquely identified by an alarm ID and an alarm name.

Object Type

Specifies the type of the object for which the alarm is generated.

Alarm Object Name

Specifies the name of the object for which the alarm is generated.

Component Type

(This parameter exists only in FusionManager.)

Specifies the name of the component for which the alarm is generated.

Generation Time

Specifies the time when the alarm is generated.

Clear Time

Specifies the time when the alarm is cleared.

Clear Mode

Specifies whether the alarm is manually or automatically cleared.

Operation

Specifies the operation that can be performed on the alarm.

Value: Manually Clear Alarm

Impact on the System

Administrators cannot manage VMs.

Possible Causes

  • IP address conflict.
  • The IP address has been changed. The alarms generated by the IP address must be manually cleared and the FusionCompute information must be reconfigured.
  • The network is faulty.
  • The FusionCompute server is not running properly.

Procedure

  1. Log in to the server where the alarm is generated using an administrator account and run the arping -c 3 -f -D -I eth0 IP address of the server where the alarm is generated command to check whether IP conflict occurs.

    • If yes, go to Step 2.
    • If no, go to Step 4.

      If the information similar to the following is displayed, no IP conflict occurs:

      ARPING 192.168.162.11 from 0.0.0.0 eth0 
      Sent 3 probes (3 broadcast(s)) 
      Received 0 response(s) 
      (Note: The IP addresses are only examples. Use the actual IP addresses.)     

      If the information similar to the following is displayed, IP conflict occurs:

      ARPING 192.168.162.11 from 0.0.0.0 eth0 
      Unicast reply from 192.168.162.11 [12:6E:D4:AB:CD:EF]  1.022ms 
      Sent 1 probes (1 broadcast(s)) 
      Received 1 response(s) 
      (Note: The preceding IP addresses and MAC addresses are only examples. Use the actual IP addresses and MAC addresses.)     

  2. Log in to the server that causes the IP conflict, shut down the server or change the server IP address, and run the arping -c 3 -f -D -I eth0 IP address of the server where the alarm is generated command again on the server where the alarm is generated to check whether the IP conflict persists.

    • If yes, contact Huawei technical support.
    • If no, go to Step 3.

  3. Choose FusionManager > Monitoring or FusionAccess > Alarm to check whether the alarm still exists.

    • If yes, go to Step 4.
    • If no, no further operation is required.

  4. Log in to the ITA server as user gandalf, and check whether the FusionCompute server network is normal. Run ping -c 3 IP address of the FusionCompute server on the CLI to check whether the network is normal.

    • If yes, go to Step 7.
    • If no, go to Step 5.

      The communication is normal if the command output is as follows:

      PING 192.168.190.2 (192.168.190.2) 56(84) bytes of data. 
      64 bytes from 192.168.190.2: icmp_seq=1 ttl=64 time=0.047 ms 
      64 bytes from 192.168.190.2: icmp_seq=2 ttl=64 time=0.057 ms 
      64 bytes from 192.168.190.2: icmp_seq=3 ttl=64 time=0.058 ms 
      (Note: The IP addresses are only examples. Use the actual IP addresses.)     

  5. Locate and rectify the network fault.
  6. Choose FusionManager > Monitoring or FusionAccess > Alarm to check whether the alarm still exists.

    • If yes, go to Step 7.
    • If no, no further operation is required.

  7. In the address box of the browser, enter the FusionAccess network address, and press Enter.

    The address format is http://service IP address of the ITA server:8081. For example, enter http://192.168.1.10:8081.

    The FusionAccess login page is displayed.

  8. Enter Username and Password.
  9. Click Login.
  10. Perform quick provisioning on the FusionAccess to check whether the FusionCompute service is running properly.

    • If yes, go to Step 11.
    • If no, contact Huawei technical support.

  11. Choose FusionManager > Monitoring or FusionAccess > Alarm to check whether the alarm still exists.

    • If yes, contact Huawei technical support.
    • If no, no further operation is required.

Related Information

None

Download
Updated: 2019-03-01

Document ID: EDOC1100010511

Views: 19803

Downloads: 11

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next