No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

eSight V300R009C00 Single-Node System Software Installation Guide (SUSE Linux) 09

Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Installing the eSight Infrastructure Manager

(Optional) Installing the eSight Infrastructure Manager

Context

NOTE:
  • The operating system version used by eSight Infrastructure Manager is SuSE Linux SP3 (64-bit).
  • eSight Infrastructure Manager and NetEco communication energy components cannot be installed at the same time.

Installing the eSight Infrastructure Management Maintenance Tool Software

The eSight Infrastructure Management Maintenance Tool is a tool for maintaining the Infrastructure Management. You can install the Infrastructure Management server software by using the eSight Infrastructure Management Maintenance Tool.

Prerequisites

You have obtained the eSight Infrastructure Management Maintenance Tool software package.

Procedure

  1. Upload eSight_VxxxRxxxCxxSPCxxx_NetEco_MTTool_SUSE.zip to the /opt/install directory on the Infrastructure Management server by using FileZilla.
  2. In Linux Operation System, use GnuPG to check the integrity of the software package.
  3. Log in to the Infrastructure Management server as user ossuser by using PuTTY.
  4. Run the following command to switch to the root user.

    su - root

    Password: root password

  5. Run the following command to decompress the eSight Infrastructure Management Maintenance Tool package.

    You must decompress the eSight Infrastructure Management Maintenance Tool package to the /opt/powerecho directory. Otherwise, you cannot use the eSight Infrastructure Management Maintenance Tool properly.

    # unzip /opt/install/eSight_VxxxRxxxCxxSPCxxx_NetEco_MTTool_SUSE.zip -d /opt/powerecho

    When the command prompt # is displayed, decompressing the eSight Infrastructure Management Maintenance Tool package is successful.

  6. Perform operations by scenario in Table 6-1.

    Table 6-1

    Option

    Description

    No dedicated IP address is planned for the eSight Infrastructure Management Maintenance Tool. The IP address of the eSight Infrastructure Management Maintenance Tool server is used as the IP address of the Infrastructure Management.

    Run the following commands to install the eSight Infrastructure Management Maintenance Tool software.

    # cd /opt/powerecho

    # chmod 700 setup.sh

    # ./setup.sh en_US

    • If the similar information is displayed, the eSight Infrastructure Management Maintenance Tool software is installed and started successfully.
      The PowerEcho service started successfully.
      Successfully installed the PowerEcho software.
    • If the following information is displayed, manually correct the time zone and time of the server, and then install the eSight Infrastructure Management Maintenance Tool software.
      The server time is incorrect. Modify it before installing the PowerEcho.

    A dedicated IP address is planned for the eSight Infrastructure Management Maintenance Tool.

    Run the following commands to install the eSight Infrastructure Management Maintenance Tool software.

    # cd /opt/powerecho

    # chmod 700 setup.sh

    # ./setup.sh en_US eSight Infrastructure Management Maintenance Tool IP address

    • If the similar information is displayed, the eSight Infrastructure Management Maintenance Tool software is installed and started successfully.
      The PowerEcho service started successfully.
      Successfully installed the PowerEcho software.
    • If the following information is displayed, manually correct the time zone and time of the server, and then install the eSight Infrastructure Management Maintenance Tool software.
      The server time is incorrect. Modify it before installing the PowerEcho.

Logging In to the eSight Infrastructure Management Maintenance Tool

The eSight Infrastructure Management Maintenance Tool uses the browser/server (B/S) working mode. You can manage and maintain the Infrastructure Management system server after logging in to the eSight Infrastructure Management Maintenance Tool over the browser on a PC.

Prerequisites

  • The browser version is Internet Explorer 9/10/11, Firefox 38ESR, Chrome 43.
    NOTE:

    To achieve better WebUI viewing effect, you are advised to use Internet Explorer 11 and set the resolution of the PC to 1366x768 or higher.

  • The IP address of the Infrastructure Management server has been obtained.
  • The PC communicates with the Infrastructure Management server properly.

Procedure

  1. In the browser address bar, enter https://IP address of the Infrastructure Management server:32804/, and then press Enter.
  2. Enter the User Name, Password and Verification code on the login page and click Log In.

    NOTE:

    The default user name for theeSight Infrastructure Management Maintenance Tool is admin and the default password is Changeme_123. You need to change the password periodically (at an interval of 60 days) to improve system security.

    After you enter the incorrect password for three consecutive times, you must enter the verification code upon the fourth login. After you enter the incorrect password for five consecutive times, the user account or the IP address is locked.

Follow-up Procedure

To exit the eSight Infrastructure Management Maintenance Tool, click Log Out in the upper-right corner of the page or close the browser.

Uploading Software Package to the Server

This section describes how to upgrade files. Before installing the Infrastructure Management software, you need to upload the target software packages to the eSight Infrastructure Management Maintenance Tool.

Prerequisites

Procedure

  1. In the navigation tree on the left side, choose Infrastructure Management Installation&Upgrade > Upload File.
  2. In the Upload File window, click Add files to select the files you want to upload.

    NOTE:
    • The Infrastructure Management software package and NE mediation software package can be selected at the same time. After the upload, they can be installed in one-click mode. After the Infrastructure Management software is installed, the NE mediation software is automatically installed in the Infrastructure Management system.

    • To delete the file, click on the right.

  3. Click Start upload to upload the files.

Installing the Infrastructure Management Software by Using the eSight Infrastructure Management Maintenance Tool

This section describes how to install the Infrastructure Management software by using the eSight Infrastructure Management Maintenance Tool client.

Prerequisites

Procedure

  1. Install the MySQL database.
    1. In the navigation tree on the left side, choose Infrastructure Management Installation&Upgrade > Install Database.
    2. Click Refresh to refresh the software package list.
    3. Select the target Infrastructure Management software package.
    4. Click One-Click Installation. Type the Password for eSight Infrastructure Management Maintenance Tool. In the displayed dialog box, click Confirm.

      The database has been installed successfully when the following information is displayed in the Details area:

      Install database success.

  2. Install the Infrastructure Management software.
    1. In the navigation tree on the left side, choose Infrastructure Management Installation&Upgrade > Install Infrastructure Management And Mediation.

      NOTE:

      Infrastructure Management installation directory is /opt/neteco by default.

    2. Select the target software package.
    3. Select whether to install the upper-layer NMS.

      NOTE:
      • Select Install the upper-layer NMS, eSight Infrastructure Management Maintenance Tool will install upper-layer NMS on the Infrastructure Management server.
      • Clear the check boxes of Install the upper-layer NMS, eSight Infrastructure Management Maintenance Tool will install lower-layer NMS on the Infrastructure Management server.

    4. Select the language of the target Infrastructure Management software package.
    5. Type Database Password(sysuser).

      The preset password of sysuser is Changeme_123. For system security purposes, change the password and keep it secure. For details, see section Changing the Passwords of MySQL Database Users in eSight Maintenance Guide.

    6. Click One-Click Installation. In the displayed dialog box, click Confirm.

      The Infrastructure Management software has been installed successfully when the following information is displayed in the Details area:

      Succeed installing the NetEco.

Download
Updated: 2019-05-17

Document ID: EDOC1100011860

Views: 92470

Downloads: 138

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next