No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

SUN2000-(50KTL, 60KTL, 65KTL)-M0 User Manual

This document describes the SUN2000-50KTL-M0, SUN2000-60KTL-M0 and SUN2000-65KTL-M0 in terms of its installation, electrical connections, commissioning, maintenance, and troubleshooting.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Powering On the SUN2000

Powering On the SUN2000

Precautions

Before turning on the AC switch between the SUN2000 and the power grid, use a multimeter to check that the AC voltage is within the specified range.

Procedure

  1. Turn on the AC switch between the SUN2000 and the power grid.

    If you perform 2 before 1, the SUN2000 reports a fault about abnormal shutdown. You can start the SUN2000 only after the fault is automatically rectified.

  2. Turn on the DC switch at the bottom of the SUN2000.
  3. Connect a mobile phone that runs the SUN2000 app to the inverter using a Bluetooth module, a WLAN module, or a USB data cable.

    Figure 6-1 Connection mode
    NOTE:
    • Purchase a Bluetooth module or a WLAN module bundled with the inverter. A Bluetooth module or a WLAN module purchased from any other source may not support communication between the inverter and the SUN2000 app.
    • Use the USB data cable delivered with the mobile phone. The port type is USB 2.0.
    • The screen snapshots in this document correspond to app 3.2.00.001 (Android).
    Figure 6-2 Login screen
    Figure 6-3 Selecting a connection mode

  4. Tap the user name area on the SUN2000 app to switch between Common User, Advanced User, and Special User.

    Figure 6-4 Switching the user
    NOTE:
    • The login password is the same as that for the SUN2000 connected to the app and is used only for the SUN2000 to connect to the app.
    • When the WLAN connection is used, the initial name of the WLAN hotspot is Adapter-WLAN module SN, and the initial password is Changeme.
    • The initial passwords for Common User, Advanced User, and Special User are all 00000a.
    • Use the initial password upon first power-on and change it immediately after login. To ensure account security, change the password periodically and keep the new password in mind. Not changing the initial password may cause password disclosure. A password left unchanged for a long period of time may be stolen or cracked. If a password is lost, devices cannot be accessed. In these cases, the user is liable for any loss caused to the PV plant.
    • During login, if five consecutive invalid password attempts are made (the interval between two consecutive attempts is less than 2 minutes), the account will be locked for 10 minutes. The password should consist of 6 characters.

  5. Enter the password and tap Log In.
  6. After successful login, the quick settings screen or main menu screen is displayed.

    NOTE:
    • If you log in to the SUN2000 app after the device connects to the app for the first time or factory defaults are restored, the quick settings screen will be displayed, on which you can set basic parameters. After the settings take effect, you can enter the main menu screen and modify the parameters on the Settings screen.If the AC switch between the inverter and the power grid is turned on but all DC switches on the inverter are not in the ON position, Grid code is not displayed on the quick settings screen.
    • You are advised to log in to the Quick Settings screen as Advanced User for parameter settings.
    • Set the correct grid code based on the application region and scenario of the SUN2000.
    Figure 6-5 Quick Settings screen (advanced user)
    NOTE:
    • Set the grid code that applies to the country or region where the PV plant is located and the SUN2000 model.
    • Set user parameters based on the current date and time.
    • Set Baud rate, Protocol, and Address based on site requirements. Baud rate can be set to 4800, 9600, or 19200. Protocol can be set to MODBUS RTU, and Address can be set to any value in the range of 1 to 247.
    • When multiple SUN2000s communicate with the SmartLogger over RS485, the RS485 addresses for all the SUN2000s on each RS485 route must be within the address range set on the SmartLogger and cannot be duplicate. Otherwise, the communication will fail. In addition, the baud rates of all the SUN2000s on each RS485 route must be consistent with the SmartLogger baud rate.
    Figure 6-6 Function menu screen

Updated: 2019-10-12

Document ID: EDOC1100016052

Views: 8038

Downloads: 2292

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next