No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Agile POL Solution Configuration Guide 02

This document describes the service configuration guide for Huawei Agile POL solution, including enterprise campus, hotel, and campus scenarios. Service configuration cases include data, IP phone, Wi-Fi, VoD, and video surveillance.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the Camera Access Service

Configuring the Camera Access Service

The OLT is connected to the remote ONU through a GPON port, ONU is connected to the camera through a ethernet port, camera provide user with video monitor service.

Prerequisites

The ONU is added to the OLT.

Data planning

Table 4-7  Data planning

Item

Data

Traffic profile

  • profile name: traffic_table_videomonitor
  • CIR: off
  • priority: 5

ONU line profile

Profile name: pol_line_all

GEM port ID: 16

Networking data

Uplink port: 0/2/0

PON access port: 0/1/0

ONU ID: 3

VLAN Planning

Single VLAN tag
  • S-VLAN ID: 200
  • C-VLAN ID: 200
  • VLAN type: smart
  • VLAN attribute: common

Procedure

  1. Configure a traffic profile.

    Run the display traffic table ip command to query existing traffic profiles in the system. If the traffic profiles existing in the system do not meet the requirements, you need to run the traffic table ip command to add a traffic profile.

    Set the profile name to traffic_table_videomonitor, the CIR to off, and the priority to 5. Packets are scheduled according to the priority specified in the profile.

    huawei(config)#traffic table ip name traffic_table_videomonitor cir off priority 5 priority-policy local-setting
    

  2. Configure the mapping between a GEM port and a VLAN.

    The service flow of user VLAN 200 is mapped to GEM port 16, respectively in the ONU line profile.

    huawei(config)#ont-lineprofile gpon profile-name pol_line_all 
    huawei(config-gpon-lineprofile-1)#gem mapping 16 1 vlan 200
    huawei(config-gpon-lineprofile-1)#commit 
    huawei(config-gpon-lineprofile-1)#quit

  3. Configure the VLAN of the Ethernet port on the ONU.

    Add ethernet port 1 to VLAN 200 in the ONU service profile.

    huawei(config)#ont-srvprofile gpon profile-name pol_ser
    huawei(config-gpon-srvprofile-1)#port vlan eth 1 200
    huawei(config-gpon-srvprofile-1)#commit
    huawei(config-gpon-srvprofile-1)#quit

  4. Configure the native VLAN of the ONU port.

    The native VLAN ID for Ethernet port 1 on the ONU is 200.

    huawei(config)#interface gpon 0/1
    huawei(config-if-gpon-0/1)#ont port native-vlan 0 3 eth 1 vlan 200
    huawei(config-if-gpon-0/1)#quit

  5. Create a service VLAN and add an upstream port to it.

    Add upstream port 0/2/0 to VLAN 200.

    huawei(config)#vlan 200 smart
    huawei(config)#port vlan 200 0/2 0

  6. Create service flow.

    Create service flow, set the service VLAN to 200, GEM port ID to 16, and user VLAN to 200, and use traffic profile traffic_table_videomonitor.

    huawei(config)#service-port vlan 200 gpon 0/1/0 ont 3 gemport 16 multi-service user-vlan 200 tag-transform translate inbound traffic-table name traffic_table_videomonitor outbound traffic-table name traffic_table_videomonitor

  7. (Option) Configure the power over Ethernet (PoE) function for an ONU Ethernet port.

    Create the maximum PoE class of an ONT Ethernet port class 3.

    huawei(config)#interface gpon 0/1
    huawei(config-if-gpon-0/1)#ont port poe 0 3 eth 1 enable max-power-class class3
    huawei(config-if-gpon-0/1)#quit
    NOTE:

    To check whether a device supports PoE, see the corresponding product documentation. PoE cannot be implemented on a device that does not support it.

  8. Save the data.

    huawei(config)#save

Configuration Script

traffic table ip name traffic_table_videomonitor cir off priority 5 priority-policy local-setting
ont-lineprofile gpon profile-name pol_line_all 
gem mapping 16 1 vlan 200
commit 
quit
ont-srvprofile gpon profile-name pol_ser
port vlan eth 1 200
commit
quit
interface gpon 0/1
ont port native-vlan 0 3 eth 1 vlan 200
quit
vlan 200 smart
port vlan 200 0/2 0
service-port vlan 200 gpon 0/1/0 ont 3 gemport 16 multi-service user-vlan 200 tag-transform translate inbound traffic-table name traffic_table_videomonitor outbound traffic-table name traffic_table_videomonitor
interface gpon 0/1
ont port poe 0 3 eth 1 enable max-power-class class3
quit 
save
Translation
Download
Updated: 2018-10-22

Document ID: EDOC1100016413

Views: 62493

Downloads: 392

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next