No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OSN 500 550 580 V100R008C50 Commissioning and Configuration Guide 02

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Modifying the Service Configuration Data

Modifying the Service Configuration Data

You can modify the existing service configuration data according to the requirements.

Context

NOTE:

During batch service deactivation, ensure that the number of services to be deactivated is smaller than 500. Simultaneous deactivation of 500 or more services will fail.

Modifying SDH Services

To modify an SDH service, you can use the modification function of the U2000, or delete the service and then create the cross-connection again.

Prerequisites

You are an NM user with Operator Group rights or higher.
Precautions

Performing this operation interrupts the service that you modify.

Procedure

  1. In the NE Explorer, select an NE and choose Configuration > SDH Service Configuration from the Function Tree.
  2. Select a cross-connection and choose Display > Expand to Unidirectional.
  3. If the service to be modified is active, you should deactivate the service. Select the service that you need to modify and then click Deactivate.

    Deactivation interrupts the services.

  4. Click OK in the Confirm dialog box that is displayed third. The Operation Result dialog box is displayed, indicating that the operation is successful.
  5. Click Close.
  6. After the cross-connection is deactivated, modify the SDH service by using the method described in 7 or 8.

    NOTE:
    • By using the method described in 7, you can modify the source or sink of a service. Ensure that the service source and sink are located on the same board before and after the modification.
    • If the modification requirement cannot be met by using the method described in 7 (for example, a pass-through service needs to be configured to the local equipment through modification), you can delete the original service and create the cross-connection again by using the method described in 8.

  7. Optional: To modify the SDH service, choose Modify from the shortcut menu.
    1. Right-click the service that you need to modify and choose Modify from the shortcut menu. Then, the Modify SDH Service dialog box is displayed.
    2. Change Source VC4 or Sink VC4, Source Timeslot Range, and Sink Timeslot Range.

      NOTE:

      By using this method, you can change only Source VC4 or Sink VC4. The source VC-4 and sink VC-4 cannot be modified at the same time.

    3. Click OK. Then, the Operation Result dialog box is displayed, indicating that the operation is successful.
    4. Click Close.
    5. Select the service that is modified and click Activate.
    6. Click OK. Then, the Operation Result dialog box is displayed, indicating that the operation is successful.
    7. Click Close.
  8. Optional: To modify the SDH service, delete the service and then create the service again.
    1. Select the service that you need to modify and click Delete.
    2. Click OK. Then, the Operation Result dialog box is displayed, indicating that the operation is successful.
    3. Click Close. The service is deleted.
    4. Create the service again according to the requirements. For details, see Creating SDH Services.

Deleting SDH Services

You can delete an existing SDH service.

Prerequisites

You are an NM user with Operator Group rights or higher.

Procedure

  1. In the NE Explorer, select an NE and choose Configuration > SDH Service Configuration from the Function Tree.
  2. Click Query to query the existing services.
  3. If the service to be deleted is active, you should deactivate the service first. Select the service that you need to delete and click Deactivate.

    Deactivation interrupts the services.

  4. Select the service to be deleted and click Delete.
  5. Click OK in the Confirm dialog box that is displayed.
  6. Click Close in the Operation Result dialog box indicating that the operation succeeded.

Deleting Ethernet Private Line Services

Ethernet private line services need to be deleted when the Ethernet boards that are configured with the Ethernet private line services need to be deleted or when the service configuration is incorrect.

Prerequisites

You are an NM user with Operator Group rights or higher.

Procedure

  1. In the NE Explorer, select an Ethernet board and then choose Configuration > Ethernet Service > Ethernet Line Service from the Function Tree.
  2. Click Query.
  3. Select the Ethernet private line service to be deleted and click Delete. Click OK in the Prompt dialog box that is displayed. Then, a dialog box is displayed, indicating that the operation is successful, that is, the Ethernet private line service is deleted successfully.
  4. Click Query to check whether the Ethernet private line service is deleted.
  5. See Deleting SDH Services to delete the cross-connections of the Ethernet private line service.

Deleting EPLAN Services

EPLAN services need to be deleted when the Ethernet boards that are configured with the EPLAN services need to be deleted or when the configuration of the EPLAN services is incorrect.

Prerequisites

You are an NM user with Operator Group rights or higher.

Context

When the EPLAN services are deleted, the VLAN unicast entries and disabled MAC address entries are deleted.

Procedure

  1. In the NE Explorer, select an Ethernet board, and then choose Configuration > Ethernet Service > Ethernet LAN Service from the Function Tree.
  2. Click Query.
  3. Select the EPLAN service to be deleted and click Delete. Click OK in the Prompt dialog box that is displayed. Then, a dialog box is displayed, indicating that the operation is successful, that is, the EPLAN service is deleted successfully.
  4. Click Query to check whether the EPLAN service is deleted.
  5. See Deleting SDH Services to delete the cross-connections of the EPLAN service.

Deleting EVPLAN Services

EVPLAN services need to be deleted when the Ethernet boards that are configured with the EVPLAN services need to be deleted or when the configuration of the EVPLAN services is incorrect.

Prerequisites

You are an NM user with Operator Group rights or higher.

Background Information

Deleting an EVPLAN service involves the following:

  1. Deleting the VLAN filtering table
  2. Deleting the service mounting configurations

Context

When the VLAN filtering table is deleted, the VLAN unicast entries and disabled MAC address entries are deleted.

Procedure

  1. In the NE Explorer, select an Ethernet board and then choose Configuration > Ethernet Service > Ethernet LAN Service from the Function Tree.
  2. Click Query.
  3. Click the VLAN Filtering tab.
  4. Select the VLAN filtering entry to be deleted and click Delete.
  5. Click the Service Mount tab.
  6. Select the EVPLAN service to be deleted and click Delete. Click OK in the Prompt dialog box that is displayed. Then, a dialog box is displayed, indicating that the operation is successful, that is, the EVPLAN service is deleted successfully.
  7. Click Query to check whether the EVPLAN service is deleted.
  8. See Deleting SDH Services to delete the cross-connections of the EVPLAN service.
Translation
Download
Updated: 2019-01-21

Document ID: EDOC1100020976

Views: 46315

Downloads: 387

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next