No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OSN 500 550 580 V100R008C50 Commissioning and Configuration Guide 02

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the Virtual Port of a Smart Line Board

Configuring the Virtual Port of a Smart Line Board

Before configuring services on a smart line board, configure virtual SDH or PKT interfaces and mapping for the board according to the service plan.

Prerequisites

Procedure

  1. Select the desired smart line board in NE Explorer and choose Configuration > Virtual Port Mapping Management from Function Tree.
  2. On the New Virtual Port tab page, add a virtual SDH or PKT interface according to the service plan, and click Add.

    Figure 1-4  Adding virtual SDH interfaces and mapping

    NOTE:

    If virtual SDH interfaces are added in a batch, ensure that the Level of all virtual interfaces are the same.

    Figure 1-5  Adding virtual PKT interfaces and mapping

  3. Click Mapped ODUk and select the desired ODUk mapping path.

    NOTE:

    To modify the mapping on a virtual interface, click Mapped ODUk and select the desired ODUk mapping path for the interface.

    Table 1-10  Parameters for adding virtual interfaces and mapping
    Parameters Values Remarks
    Type

    ETH and SDH

    Specifies the type of received/transmitted services.

    Level

    HUNS3:

    STM-16, STM-64

    Default value: STM-16

    HUND2:

    STM-16, STM-64

    Default value: STM-16

    Specifies the rate of received/transmitted services.

    Linkage with other parameters:

    This parameter can be set only when Port Type is set to SDH.

    Bandwidth

    GE, 10GE, nGE

    Default value: GE

    Specifies the bandwidth of received/transmitted services.

    Linkage with other parameters:

    This parameter can be set only when Port Type is set to ETH.

    Quantity

    1 to 32

    Default value: 1

    NOTE:

    The value range of this parameter depends on the number of configured virtual ports and the remaining available virtual port resources.

    Specifies the number of virtual interfaces to be added.

    Linkage with other parameters:

    When Port Type is set to SDH:

    • A maximum of four virtual interfaces are supported by HUNS3 and a maximum of two virtual interfaces are supported by HUND2 if Level is set to STM-64.
    • A maximum of eight virtual interfaces are supported by HUND2 and a maximum of 16 virtual interfaces are supported by HUNS3 if Level is set to STM-16.

    When Port Type is set to ETH:

    • A maximum of 16 virtual interfaces are supported by HUND2 and a maximum of 32 virtual interfaces are supported by HUNS3 if Bandwidth is set to GE.
    • A maximum of 16 virtual interfaces are supported by HUND2 and a maximum of 32 virtual interfaces are supported by HUNS3 if Bandwidth is set to nGE.
    • A maximum of 2 virtual interfaces are supported by HUND2 and a maximum of 4 virtual interfaces are supported by HUNS3 if Bandwidth is set to 10GE.
    Port Type

    ETH and SDH

    Specifies the type of received/transmitted services.

    Port
    • ETH: 40001 (V_ETH-1) to 40032 (V_ETH-32)
    • SDH: 51 (V_SDH-1) to 66 (V_SDH-16)

    Specifies the ID of a virtual interface.

    NOTE:

    SDH virtual ports are classified into four groups: 51(V_SDH-1) to 54(V_SDH-4), 55(V_SDH-5) to 58(V_SDH-8), 59(V_SDH-9) to 62(V_SDH-12), and 63(V_SDH-13) to 66(V_SDH-16). When configuring SDH virtual ports, observe the following requirements:

    • Only the following four SDH virtual ports can be provisioned with STM-64 services: 51(V_SDH-1), 55(V_SDH-5), 59(V_SDH-9), and 63(V_SDH-13).
    • In each group of SDH virtual ports, if one port is provisioned with an STM-16 service, the remaining ports cannot be provisioned with STM-64 services. For example, if an STM-16 service is configured on the 52(V_SDH-2) port, the remaining three ports cannot be provisioned with STM-64 services: 51(V_SDH-1), 53(V_SDH-3) and 54(V_SDH-4).
    • When configuring STM-16 services for the virtual ports, prefer to use the consecutive ports. For example, to configure STM-16 services on five of the SDH virtual ports, use 51(V_SDH-1), 52(V_SDH-2), 53(V_SDH-3), 54(V_SDH-4), and 55(V_SDH-5).
    Mapped ODUk

    The available mapping path is related to the type of universal line board, the port type and level/bandwidth that have been set.

    Specifies the ID of the physical port on which the ODUk mapped to a virtual interface resides.

    Occupied ODTUk Timeslots

    For example, 8

    Specifies the number of ODTUk timeslots occupied by the ODUk mapped to a virtual interface.

    Linkage with other parameters:

    This parameter can be set only when Port Type is set to ETH and the level of Mapped ODUk is ODUflex.

  4. Click Apply. The Result dialog box is displayed, indicating that the operation is successful.
  5. Click Close.

Follow-up Procedure

If the proportion between SDH services and PKT services on the smart line board needs to be adjusted, you can adjust the number of virtual interfaces as follows:

  1. Select a virtual interface and click Delete. In the Confirm dialog box that is displayed, click OK.
  2. Add new virtual interfaces according to 1 to 5.
Translation
Download
Updated: 2019-01-21

Document ID: EDOC1100020976

Views: 57834

Downloads: 487

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next