No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OSN 500 550 580 V100R008C50 Commissioning and Configuration Guide 02

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Services on the Non-Protection Chain

Configuring Services on the Non-Protection Chain

Configure the protection subnet and the services on the non-protection chain separately. It is recommended that you configure the protection subnet before configuring the services on the non-protection chain.

Networking Diagram

You can configure a non-protection chain if the services on the chain need not be protected. In this case, all the timeslots on the chain can carry services.

Figure 2-1 shows a point-to-point non-protection chain. In this example, the SP3D boards are configured on the source NE (NE1) and the sink NE (NE2) as tributary boards to add and drop services, and the SL1D boards are used as line boards to transmit SDH services.

Figure 2-1  Networking diagram of the non-protection chain

NOTE:

This topic considers the OptiX OSN 550 as an example to describe the board layout. In the case of other products, the configuration method is the same, except for the slots. For the slot information, see the Hardware Description of the relevant product.

Signal Flow and Timeslot Allocation

To configure services on the non-protection chain, you need to plan the traffic direction and timeslot allocation for the services on the non-protection chain.

Figure 2-2 shows the signal flow and timeslot allocation. In this example, five E1 services are added to or dropped from NE1 and NE2.

Figure 2-2  Signal flow and timeslot allocation of the services on the non-protection chain

Per-NE Configuration Procedure

The configuration of services on the non-protection chain is not related to the configuration of the protection subnet. To configure the services on the non-protection chain, configure the SDH services from the tributary board to the line board on the source and sink NEs if the protection subnet is already created.

Prerequisites

  • The physical topology of the network must be created.
  • The NEs, boards, and fibers must be created on the U2000.
  • The created protection subnet must be consistent with the actual network topology. For details about how to create the protection subnet, see Configuring a Non-Protection Chain.
  • You must be familiar with the information about Signal Flow and Timeslot Allocation.

Procedure

  1. Configure SDH services on the source NE (NE1).
    1. Select NE1 in the NE Explorer, and then choose Configuration > SDH Service Configuration from the Function Tree.
    2. Click Create on the lower-right pane to display the Create SDH Service dialog box. Set the parameters that are required, and then click OK,

      Parameter Value in This Example Description
      Level VC12 In this example, E1 services are configured. Hence, Level of the E1 services is set to VC12.
      Direction Bidirectional In this example, the services are transmitted and received over the same path. That is, the services are Bidirectional services.
      Source Slot 3-SP3D In this example, the SP3D board in slot 3 of NE1 is configured as the source tributary board. See Figure 2-2.
      Source VC4 - -
      Source Timeslot Range(e.g.1,3-6) 1-5 In this example, five E1 services are configured between NE1 and NE2. Hence, the service source occupies VC-12s 1-5.
      Sink Slot 1-SL1D-1(SDH-1) In this example, the SL1D board in slot 1 of NE1 is configured as the sink line board. See Figure 2-2.
      Sink VC4 VC4-1 The service sink uses the timeslots of VC4-1.
      Sink Timeslot Range(e.g.1,3-6) 1-5 In this example, five E1 services are configured between NE 1 and NE2. Hence, the service sink occupies VC-12s 1-5.
      Activate Immediately Yes -

  2. Refer to 1 and configure SDH services on the sink NE (NE2). Set the parameters as follows.

    Parameter Value in This Example Description
    Level VC12 In this example, E1 services are configured. Hence, Level of the E1 services is set to VC12.
    Direction Bidirectional In this example, the services are transmitted and received over the same path. That is, the services are Bidirectional services.
    Source Slot 3-SP3D In this example, the SP3D board in slot 3 of NE1 is configured as the source tributary board. See Figure 2-2.
    Source VC4 - -
    Source Timeslot Range(e.g.1,3-6) 1-5 In this example, five E1 services are configured between NE1 and NE2. Hence, the service source occupies VC-12s 1-5.
    Sink Slot 1-SL1D-1(SDH-1) In this example, the SL1D board in slot 1 of NE1 is configured as the sink line board. See Figure 2-2.
    Sink VC4 VC4-1 The service sink uses the timeslots of VC4-1.
    Sink Timeslot Range(e.g.1,3-6) 1-5 In this example, five E1 services are configured between NE1 and NE2. Hence, the service sink occupies VC-12s 1-5.
    Activate Immediately Yes -

  3. Check whether the services are configured correctly. For details, see Verifying the Correctness of the SDH Service Configuration.
  4. Enable the performance monitoring function of the NEs. For details, see Setting Network-Wide Performance Monitoring.
  5. Back up the configuration data of the NEs. For details, see Backing Up the NE Data to the System Control Board.
Relevant Task

If the services are configured incorrectly and need to be deleted, see Deleting SDH Services.

End-to-End Configuration Process

The configuration of services on a non-protection chain is independent of the creation of the protection subnet. To configure the services on the non-protection chain, configure the SDH services from the tributary board to the line board on the source and sink NEs if the protection subnet is already created.

Prerequisites

  • The physical network topology must be set up.
  • The NEs, boards, and fibers must be successfully created on the U2000.
  • The protection subnet must be created and must be the same as the actual topology. For details about how to create the protection subnet, see Configuring a Non-Protection Chain.
  • The operator must understand the information provided in Signal Flow and Timeslot Allocation.

Procedure

  1. Choose Service > SDH Trail > Create SDH Trail from the Main Menu.
  2. Create the VC-4 service-layer trail.
    1. Configure the parameters as follows. Set Level to VC4 Server Trail. The other parameters take default values.

    2. Double-click the source NE (NE1) and sink NE (NE2) on the right of the main topology and click Apply. Then, click Close in the Operation Result dialog box indicating that the operation succeeded.
    3. Optional: In the Operation Result dialog box indicating that the operation succeeded, click Browse Trail to query the created VC4 service-layer trail.
  3. Create VC12 services.
    1. In Create SDH Tail, configure the parameters as follows. Set Level to VC12. The other parameters take default values.

    2. Double-click the source NE on the right of the main topology. The Select Board Port-Source dialog box is displayed. Select the required PDH board and Tributary Port. Click OK.
    3. Double-click the sink NE (NE2) on the right of the main topology. Configure NE2 in the same manner.
    4. Select Copy after Creation and click Apply. Click Close in the Operation Result dialog box indicating that the operation succeeded. Then, the Copy dialog box is displayed.
    5. In Available Timeslots/Port, select the ports from NE1-Slot3-SP3D-2(SDH_TU-2) to NE2-Slot3-SP3D-5(SDH_TU-5), and click Add, and then click OK.
    6. In the Operation Result dialog box indicating that the operation succeeded, click Close.
    7. Optional: In the Operation Result dialog box indicating that the operation succeeded, click Browse Trail to query the created VC12 services.
  4. Check whether the service configuration is correct. For details, see Verifying the Correctness of the SDH Service Configuration.
  5. Enable the performance monitoring function of the NEs. For details, see Setting Network-Wide Performance Monitoring.
  6. Back up the configuration data of the NEs. For details, see Backing Up the NE Data to the System Control Board.
Relevant Task

If the services are configured incorrectly and thus need to be deleted, see Deleting SDH Services.

Translation
Download
Updated: 2019-01-21

Document ID: EDOC1100020976

Views: 45361

Downloads: 378

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next