No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

PowerCube 500 System Configuration Guide (PC500-300H1, PC500-300G1, EG6P-150G1)

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring IEEE 802.1q Bridge-based E-LAN Services

Configuring IEEE 802.1q Bridge-based E-LAN Services

This section uses an IEEE 802.1q bridge-based E-LAN service as an example to describe how to configure Ethernet services according to the service plan.

Networking Diagram

As shown in Figure 2-6, the service requirements are as follows:
  • The PowerCube 500 needs to transmit Ethernet services from Camera 1 and Camera 2 to the upper-layer network based on IEEE 802.1q bridge-based E-LAN services.
  • Services from Camera 1 and Camera 2 need to be isolated using VLAN IDs.
    • The VLAN ID is set to 100 for services from between Camera 1 to the Power Cube 500.
    • The VLAN ID is set to 200 for services from between Camera 2 to the Power Cube 500.
Figure 2-6 Networking diagram for configuring IEEE 802.1q bridge-based E-LAN services

Data Preparation

The following table describes the data planned for the configuration.

Table 2-7 Data planned for the configuration

Item

Parameter

Value for Ethernet Services from Camera 1 to the PowerCube 500

Value for Ethernet Services from Camera 2 to the PowerCube 500

Planning Guidelines

Setting the basic attributes of the ports

Port Enabled

Enabled

Enabled

Set this parameter to Enabled.

Encapsulation Type

802.1Q

802.1Q

Set this parameter to 802.1Q when configuring IEEE 802.1q bridge-based E-LAN services.

Working Mode

Auto-Negotiation

Auto-Negotiation

Set this parameter to the same value as that at the peer end. Typically, this parameter is set to Auto-Negotiation at the peer end.

Setting the layer 2 attributes of the ports

Tag

Tag Aware

Tag Aware

In this example, all services carry VLAN IDs. Therefore, set Tag to Tag Aware for all service ports.

If none of the received services carries VLAN IDs, add the default VLAN to the ports. That is, set Tag to Access, and set the Default VLAN ID and VLAN priority. For details, see Setting the Layer 2 Attributes of Ethernet Ports.

Configuring an IEEE 802.1q bridge-based E-LAN service

Service ID

1

2

Value range: 1 to 1024.

Service Name

ELAN

ELAN1

-

Tag Type

C-Aware

C-Aware

Set this parameter to C-Aware when configuring IEEE 802.1q bridge-based E-LAN services.

MAC Address Learning Mode

IVL

IVL

Set this parameter to IVL when configuring IEEE 802.1q bridge-based E-LAN services.

UNI Port

  • 2-EG8P-3(PORT-3)
  • 2-EG8P-5(PORT-5)
  • 2-EG8P-4(PORT-4)
  • 2-EG8P-5(PORT-5)

Set this parameter according to the service plan.

VLAN

100

200

-

Others

Default value

Default value

-

Procedure

  1. Set the basic attributes of the ports.

    Ethernet services from Camera 1 to the PowerCube 500 are used as an example.

  2. Set the layer 2 attributes of the ports.

    Ethernet services from Camera 1 to the PowerCube 500 are used as an example.



  3. Configure an IEEE 802.1q bridge-based E-LAN service.

    Ethernet services from Camera 1 to the PowerCube 500 are used as an example.

Translation
Download
Updated: 2019-04-26

Document ID: EDOC1100021621

Views: 21681

Downloads: 242

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next