No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

PowerCube 500 System Configuration Guide (PC500-300H1, PC500-300G1, EG6P-150G1)

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring VLAN-based E-Line Services

Configuring VLAN-based E-Line Services

This section uses a VLAN-based E-Line service as an example to describe how to configure Ethernet services according to the service plan.

Networking Diagram

As shown in Figure 2-2, the service requirements are as follows:

  • The PowerCube 500 needs to transmit Ethernet services from Camera 1 and Camera 2 to the upper-layer network based on VLAN-based E-Line services.
  • Services from Camera 1 and Camera 2 need to be isolated using VLAN IDs.
    • The VLAN ID is set to 100 for services from between Camera 1 to the Power Cube 500.
    • The VLAN ID is set to 200 for services from between Camera 2 to the Power Cube 500.
Figure 2-2 Networking diagram for transmitting VLAN-based E-Line services

Data Preparation

The following table describes the data planned for the configuration.

Table 2-2 Data planned for the configuration

Item

Parameter

Value for Ethernet Services from Camera 1 to the PowerCube 500

Value for Ethernet Services from Camera 2 to the PowerCube 500

Planning Guidelines

Setting the basic attributes of the ports

Port Enabled

Enabled

Enabled

Set this parameter to Enabled.

Encapsulation Type

802.1Q

802.1Q

Set this parameter to 802.1Q when configuring VLAN-based E-Line services.

Working Mode

Auto-Negotiation

Auto-Negotiation

Set this parameter to the same value as that at the peer end. Typically, this parameter is set to Auto-Negotiation at the peer end.

Setting the layer 2 attributes of the ports

Tag

Tag Aware

Tag Aware

In this example, all services carry VLAN IDs. Therefore, set Tag to Tag Aware for all service ports.

If none of the received services carries VLAN IDs, add the default VLAN to the ports. That is, set Tag to Access, and set the Default VLAN ID and VLAN priority. For details, see Setting the Layer 2 Attributes of Ethernet Ports.

Configuring a VLAN-based E-Line service

Service ID

1

2

Value range: 1 to 1024.

Service Name

NodeAtoPC500

NodeBtoPC500

-

Source Interface

2-EG8P-3(PORT-3)

2-EG8P-4(PORT-4)

-

Source VLAN ID

100

200

-

Set this parameter according to the service plan.

Sink Interface

2-EG8P-5(PORT-5)

2-EG8P-5(PORT-5)

-

Sink VLAN ID

100

200

The VLAN ID for the source port must be the same as that for the sink port.

Procedure

  1. Set the basic attributes of the ports.

    Ethernet services from Camera 1 to the PowerCube 500 are used as an example.

  2. Set the layer 2 attributes of the ports.

    Ethernet services from Camera 1 to the PowerCube 500 are used as an example.



  3. Configure a VLAN-based E-Line service.

    Ethernet services from Camera 1 to the PowerCube 500 are used as an example.

Translation
Download
Updated: 2019-04-26

Document ID: EDOC1100021621

Views: 21562

Downloads: 241

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next