No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionAccess V100R006C20 on FusionCloud V100R006C10 Software Installation Guide 11 (Microsoft AD)

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring FusionManager

Configuring FusionManager

Installing Tools

Scenarios

This section describes how to install UVP Tools for the created VM.

Prerequisites

You have obtained the password for logging in to FusionSphere OpenStack OM.

Procedure
  1. Log in to FusionSphere OpenStack OM and choose Resources > Computing > Compute Instances.
  2. Locate the row that contains the VM created in Creating VMs, and choose More > Stop.
  3. After the VM is stopped, choose More > Attach uvptools and mount UVP Tools.
  4. Click Start. After the VM is started, choose More > VNC Login.
  5. Use the galaxmanger account to log in to the VM. The default password is Huawei@CLOUD8.
  6. Run the gotoEngineerMode command and enter the password to switch to user root. The default password is Huawei@CLOUD8!.
  7. Run the following command to create the temporary directory /mnt/vmtools:

    mkdir -p /mnt/vmtools

  8. Run the following command to mount UVPTools:

    mount /dev/sr1 /mnt/vmtools

  9. Run the following command to go to the /mnt/vmtools directory and query the file:

    cd /mnt/vmtools && ll

  10. Run the following command to copy the vmtools-XXX.tar.bz2 file to the /root directory:

    cp vmtools-XXX.tar.bz2 /root

  11. Run the following command to go to the /root directory and decompress the vmtools-XXX.tar.bz2 file:

    cd /root && tar -xjf vmtools-XXX.tar.bz2

  12. Run the following command to go to the /root/vmtools directory and install UVP VMTools:

    cd /root/vmtools && ./install

    If the following information is displayed, UVP VMTools is successfully installed and the system takes effect after the system is restarted:

    The UVP VMTools is installed successfully. 
    Reboot the system for installation to take effect.

  1. Locate the row that contains the FusionSphere OpenStack OM VM, choose More > Detach uvptools, and uninstall UVP Tools.

Modifying the NIC Information

Scenarios

This section guides how to modify the NIC information of a VM.

Prerequisites

You have obtained the gateway address of the DMZ_Service network segment.

Procedure
  1. Use the galaxmanger account to log in to the VM using VNC. The default password is Huawei@CLOUD8.
  2. Run the gotoEngineerMode command and enter the password to switch to user root. The default password is Huawei@CLOUD8!.
  3. Run the vi /etc/sysconfig/network/ifcfg-eth0 command, press I to enter the editing mode, and modify the eth0 information of the NIC according to the following configuration:

    BOOTPROTO="dhcp" 
    DEVICE="eth0"
    IPADDR="" 
    NETMASK="" 
    STARTMODE="onboot"
    GATEWAY="Gateway address of the DMZ_Service network segment"

  1. Press Esc to exit the editing mode, enter :wq, and press Enter.
  2. Run the vi /etc/sysconfig/network/ifcfg-eth1 command, press I to enter the editing mode, and modify the information about the NIC eth1 as follows:

    BOOTPROTO="dhcp" 
    DEVICE="eth1"
    IPADDR="" 
    NETMASK=""
    STARTMODE="onboot"

  1. Press Esc to exit the editing mode, enter :wq, and press Enter.
  2. Run the service network restart command to restart the network.

Adding a Route

Scenarios

This section describes how to add a route for the VM.

Prerequisites
  • The network segment of the FIP in the POD zone has been obtained.
  • You have obtained the gateway, subnet mask, and NIC ID of the DMZ_Tenant NIC of FusionManager.
Procedure
  1. Use the galaxmanger account to log in to the VM using VNC. The default password is Huawei@CLOUD8.
  2. Run the gotoEngineerMode command and enter the password to switch to user root. The default password is Huawei@CLOUD8!.
  3. Run the following command to edit a route configuration file:

    vi /etc/sysconfig/network/routes

  4. Press I to enter the editing mode and add routing information in the last row in the following format:

    FIP network segment in the POD zone Gateway subnet mask NIC ID

    Examples:

    10.64.0.0 10.125.0.1 255.255.0.0 eth1

    Table 4-26 Parameter description

    Name

    Example

    FIP network segment in the POD zone

    10.64.0.0

    Gateway of the DMZ_Tenant NIC of FusionManager.

    10.125.0.1

    Subnet mask of the DMZ_Tenant NIC of FusionManager.

    255.255.0.0

    DMZ_Tenant NIC ID of FusionManager.

    eth1

  5. Press Esc to exit the editing mode, enter :wq, and press Enter.
  6. Run the following command to restart the network:

    service network restart

Configuring FusionManager

Scenarios

This section describes how to configure FusionManager for the VM.

Prerequisites

None

Procedure
  1. Use the galaxmanger account to log in to the VM using VNC. The default password is Huawei@CLOUD8.
  2. Run the following command and select OK to navigate to the wizard:

    fmconfig

  1. Select Next to switch to the deployment mode selection page. Choose Single mode.

  1. Click Next. Set the node name and NIC eth0 as needed.

    • Node Name: specifies the FusionManager node names.
    • Local IP: IP address of the DMZ Service plane of FusionManager.
    • Netmask: Subnet mask of the DMZ Service plane of FusionManager.
    • Gateway: Gateway address of the DMZ Service plane of FusionManager.

  1. Click Next and configure the eth1 network adapter.

    • Local IP address: Specifies the IP address of the FusionManager DMZ Tenant plane.
    • Netmask: Subnet mask of the FusionManager DMZ Tenant plane.

  1. Click Next to switch to the information confirmation page.

  1. Confirm the information and select Next. Configuration starts.

    If FusionManager configured successfully is displayed, the configuration is successful.

Translation
Download
Updated: 2019-07-01

Document ID: EDOC1100021785

Views: 46396

Downloads: 100

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next