No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionAccess V100R006C20 on FusionCloud V100R006C10 Software Installation Guide 11 (Microsoft AD)

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing Components

Installing Components

Scenarios

This section describes how to install the license component, GaussDB component used by the cascading ITA, and the cascading ITA component, and how to configure the cascading ITA component.

Prerequisites

  • You have logged in to the cascading FusionSphere OpenStack management console (Region Type I scenario) or FusionSphere OpenStack management console (Region Type II scenario).
  • You have obtained the gateways of the DMZ_Service network plane and DMZ_Tenant network plane.
  • You have obtained the cascaded external_relay_network address (Region Type I scenario) or external_relay_network address (Region Type II scenario). For details, see Information Collection.

Procedure

Installing the license component

  1. Log in to the FA-Pub-License VM using VNC as user root.
  2. Run the following commands and add a default route to the License server:

    echo 'any net 0.0.0.0 netmask 0.0.0.0 gw DMZ_Service network plane gateway' >> /etc/sysconfig/static-routes

    echo 'any net cascaded external_relay_network address or external_relay_network address gw DMZ_Tenant network plane gateway dev eth1' >> /etc/sysconfig/static-routes

    For example, if the gateway of the DMZ_Service network plane is 192.168.0.1, the cascaded external_relay_network address or external_relay_network address is 10.64.0.0/15, and the gateway of the DMZ_Tenant network plane is 10.125.0.1, run the following commands:

    echo 'any net 0.0.0.0 netmask 0.0.0.0 gw 192.168.0.1' >> /etc/sysconfig/static-routes

    echo 'any net 10.64.0.0/15 gw 10.125.0.1 dev eth1' >> /etc/sysconfig/static-routes

  3. Run the following command to edit the /etc/init.d/network file:

    vi /etc/init.d/network

  4. Press I to enter the editing mode, and add ip route delete default dev eth1 before exit $rc, as shown in Figure 4-64.

    Figure 4-64 Delete the default route to the DMZ_Tenant

  5. Run the following command to restart network service.

    systemctl daemon-reload

    service network restart

  6. Enter startTools. The FusionAccess screen is displayed, as shown in Figure 4-65.

    Figure 4-65 FusionAccess

  7. Choose Software > Custom Install and press Enter.

    The Custom Install screen is displayed, as shown in Figure 4-66.

    Figure 4-66 Custom Install

  8. Select LICENSE and press Enter.

    The Install or Uninstall LICENSE page is displayed.

  9. Select Install LICENSE and press Enter.

    If the License installed successfully dialog box is displayed, the License is successfully installed.

  10. Press Enter.

Installing the GaussDB component

  1. Choose Custom Install > GaussDB and press Enter.

    The Install or Uninstall GaussDB page is displayed.

  2. Select Install GaussDB and press Enter.

    If the GaussDB installed successfully dialog box is displayed, the License is successfully installed.

  3. Press Enter.

Installing the Cascading ITA component

  1. Choose Custom Install > ITA and press Enter.

    The Install or Uninstall or Configure ITA page is displayed.

  2. Select Install ITA and press Enter.

    If the ITA installed successfully dialog box is displayed, the License is successfully installed.

  3. Press Enter.

Configuring the Cascading ITA component

  1. Choose Custom Install > ITA and press Enter.

    The Install or Uninstall or Configure ITA page is displayed.

  2. Choose Configure ITA (Common mode) and press Enter. Set parameters as described in the following table.

    Parameter

    Description

    Example Value

    DB Float IP Address

    GaussDB floating IP address. Set it to the DMZ_Service network plane IP address of the public license server.

    -

    Database User Password

    Password of ITALoginUser. Change it as needed.

    -

    Confirm Database User Password

    Password of ITALoginUser. Change it as needed.

    -

    Database Admin Password

    Password of fauser. The value is Cloud12#$.

    Cloud12#$

    If the ITA configure successfully dialog box is displayed, the cascading ITA is successfully installed.

  3. Press Enter. Exit startTools as prompted.
Translation
Download
Updated: 2019-07-01

Document ID: EDOC1100021785

Views: 46066

Downloads: 100

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next