No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionAccess V100R006C20 on FusionCloud 6.3.x Software Installation Guide 11 (LiteAD)

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the VPC

Configuring the VPC

Scenarios

This section describes how to create a VPC on the ManageOne operation plane, create a management subnet for the VPC, and service subnet.

FusionAccess can also be deployed in an existing VPC. If you deploy it in an existing VPC, do not re-create the VPC. You can create and configure subnets.

Procedure

Creating a VPC and management subnet

  1. Use a VDC administrator or VDC operator to the ManageOne operation plane and choose Network > Virtual Private Cloud.
  2. On the Dashboard page, click Apply for VPC.
  3. Set the parameters according to Table 5-1. Retain the default values for the parameters that are not involved or set the parameters according to the actual requirements. Click Apply Now.

    Table 5-1 Parameter description

    Parameter

    Description

    Example Value

    Region

    The current region is automatically displayed on the page. You can change the region in the upper left corner of the page.

    az1.dc1

    Name

    Specifies the VPC name. The name consists of only letters, digits, underscores (_), and hyphens (-).

    vpc-VDI

    Network Name

    NOTE:

    This parameter is mandatory for FusionCloud 6.3.0.

    Select the configured VPC external network.

    Select an AZ from the AZ drop-down list. Select the configured VPC external network from the AZ drop-down list.

    NOTE:

    If you select the same external network for two or more VPCs, the subnet CIDR blocks of these VPCs cannot overlap.

    dummy_external_network in AZ az1.dc1

    External Network

    NOTE:

    This parameter is mandatory for FusionCloud 6.3.1 or later.

    Choose an AZ from the first drop-down list, and choose an external network for the VPC from the second drop-down list.

    NOTE:

    Ensure that the external network can communicate with the zone where the elastic server resides.

    az1.dc1

    net-01

    Validity Period

    Specifies the validity period for a VPC.

    Not limited

    Subnet Name

    Specifies the subnet name. The name consists of only letters, digits, underscores (_), and hyphens (-).

    subnet-Manager

    CIDR

    Specifies the CIDR block for the subnet. This value must be within the VPC CIDR range.

    172.16.0.0/20

    Gateway

    Specifies the gateway address of the subnet.

    172.16.0.1

Creating a service subnet

  1. On the Virtual Private Cloud page, click VPC name vpc-VDI.
  2. Click the Subnet tab, and then click Create Subnet.
  3. On the Create Subnet page, configure parameters based on Table 5-2 and retain the default values for the parameters that are not involved.

    Table 5-2 Parameter description

    Parameter

    Description

    Example Value

    Name

    Specifies the subnet name. The name consists of only letters, digits, underscores (_), and hyphens (-).

    subnet-Desktop

    CIDR

    Specifies the CIDR block for the subnet. This value must be within the VPC subnet CIDR block.

    192.168.0.0/24

    Gateway

    Specifies the gateway address of the subnet.

    192.168.0.1

  4. Click OK.

(Optional) Applying for NAT

If the desktop VM needs to access the Internet, perform the following steps:

NOTE:

The following steps apply to Region Type I and Region Type II is set to SNAT.

  1. On the NAT tab page, click Apply for NAT.
  2. On the Apply for NAT page, configure parameters based on Table 5-3 and retain the default values for the parameters that are not involved.

    Table 5-3 Parameter description

    Parameter

    Description

    Example Value

    External Network

    Specifies the external network.

    net-01 in AZ az1.dc1

    Assignment Mode

    Specifies the EIP assignment mode.

    Automatically assigned

    Elastic IP Address

    Specifies the EIP used by ECSs in a subnet to access the Internet.

    192.168.1.35

    Subnet

    Specifies the subnet for which the SNAT function takes effect. Set this parameter to the management subnet and service subnet.

    subnet-Manager

    subnet-Desktop

  3. Click OK.
Translation
Download
Updated: 2019-07-01

Document ID: EDOC1100026752

Views: 29256

Downloads: 39

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next