No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C00 Configuration Guide - MPLS 01

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Checking the Configurations

Checking the Configurations

After the configuration of a static CR-LSP, you can view the static CR-LSP status.

Prerequisites

The static CR-LSP has been configured.

Procedure

  • Run the display mpls static-cr-lsp [ lsp-name ] [ verbose ] command to check information about the static CR-LSP.
  • Run the display mpls te tunnel [ destination ip-address ] [ lsp-id ingress-lsr-id session-id local-lsp-id ] [ lsr-role { all | egress | ingress | remote | transit } ] [ name tunnel-name ] [ { incoming-interface | interface | outgoing-interface } interface-type interface-number ] [ verbose ] command to check information about the tunnel.
  • Run the display mpls te tunnel statistics or display mpls lsp statistics command to check the tunnel statistics.
  • Run the display mpls te tunnel-interface command to check information about the tunnel interface on the ingress.

Example

If the configurations are successful, run the preceding commands to view the following information:

  • Information about the static CR-LSP name, the incoming and outgoing labels, and the incoming and outgoing interfaces. The status of CR-LSP is Up.

    <HUAWEI> display mpls static-cr-lsp
    TOTAL          : 2     STATIC CRLSP(S)
    UP             : 2     STATIC CRLSP(S)
    DOWN           : 0     STATIC CRLSP(S)
    Name                FEC                I/O Label        I/O If                     Status
    Tunnel10         3.3.3.3/32         NULL/20          -/GE1/0/6                  Up
    Tunnel20         -/32               130/NULL         GE1/0/6/-                  Up
  • Statistics about the tunnel status on the LSR.

    <HUAWEI> display mpls lsp statistics
    Lsp Type       Total     Ingress   Transit   Egress                             
    STATIC LSP     0         0         0         0
    STATIC CRLSP  1         1         0         0
    LDP LSP        7         3         3         1
    LDP IPV6 LSP   0         0         0         0
    RSVP CRLSP     2         2         0         0
    BGP LSP        0         0         0         0
    ASBR LSP       0         0         0         0
    BGP IPV6 LSP   0         0         0         0
    L3VPN IPV6 LSP 0         0         0         0
    ----------------------------------------------------------------------          
    LSP            8         4         3         1
    CRLSP          3         3         0         0
    ----------------------------------------------------------------------          
    Lsp Type       IngressLspBypassState         TransitLspBypassState              
                   ExistNotUsed   InUse          ExistNotUsed   InUse               
    RSVP CRLSP     0              0              0              0
    ----------------------------------------------------------------------
  • Detailed information about the tunnel interface, including the tunnel name, state description, and attributes. The tunnel attributes include the LSP ID, ingress, egress, and signaling protocol.

    <HUAWEI> display mpls te tunnel-interface
        Tunnel Name       : Tunnel1
        Signalled Tunnel Name: -
        Tunnel State Desc : CR-LSP is Up
        Tunnel Attributes   :     
        Active LSP          : Primary LSP                                       
        Traffic Switch      : - 
        Session ID          : 1
        Ingress LSR ID      : 1.1.1.9               Egress LSR ID: 4.4.4.9
        Admin State         : UP                    Oper State   : UP
        Signaling Protocol  : RSVP
        FTid                : 1
        Tie-Breaking Policy : None                  Metric Type  : None
        Bfd Cap             : None                  
        Reopt               : Disabled              Reopt Freq   : -              
        Auto BW             : Disabled              Threshold    : 0 percent
        Current Collected BW: 0 kbps                Auto BW Freq : 0
        Min BW              : 0 kbps                Max BW       : 0 kbps
        Offload             : Disabled              Offload Freq : - 
        Low Value           : -                     High Value   : - 
        Readjust Value      : - 
        Offload Explicit Path Name: 
        Tunnel Group        : -                                              
        Interfaces Protected: -
        Excluded IP Address : -
        Referred LSP Count  : 0  
        Primary Tunnel      : -                     Pri Tunn Sum : -              
        Backup Tunnel       : -                                                    
        Group Status        : -                     Oam Status   : -             
        IPTN InLabel        : -                     Tunnel BFD Status : -                               
        BackUp LSP Type     : None                  BestEffort   : Disabled
        Secondary HopLimit  : -
        BestEffort HopLimit  : -
        Secondary Explicit Path Name: -
        Secondary Affinity Prop/Mask: 0x0/0x0
        BestEffort Affinity Prop/Mask: 0x0/0x0  
        IsConfigLspConstraint: -
        Hot-Standby Revertive Mode:  Revertive
        Hot-Standby Overlap-path:  Disabled
        Hot-Standby Switch State:  CLEAR
        Bit Error Detection:  Disabled
        Bit Error Detection Switch Threshold:  -
        Bit Error Detection Resume Threshold:  -
        Ip-Prefix Name    : -
        P2p-Template Name : -
        PCE Delegate      : Only status report      LSP Control Status : Local control
        Entropy Label       :None 
        Associated Tunnel Group ID: -                 Associated Tunnel Group Type: -
        Auto BW Remain Time : 200 s   Reopt Remain Time  : 100 s
    
        Primary LSP ID      : 1.1.1.9:19
        LSP State           : UP                    LSP Type     : Primary
        Setup Priority      : 7                     Hold Priority: 7
        IncludeAll          : 0x0
        IncludeAny          : 0x0
        ExcludeAny          : 0x0
        Affinity Prop/Mask  : 0x0/0x0               Resv Style   :  SE
        Configured Bandwidth Information:
        CT0 Bandwidth(Kbit/sec): 20000           CT1 Bandwidth(Kbit/sec): 0
        CT2 Bandwidth(Kbit/sec): 0               CT3 Bandwidth(Kbit/sec): 0
        CT4 Bandwidth(Kbit/sec): 0               CT5 Bandwidth(Kbit/sec): 0
        CT6 Bandwidth(Kbit/sec): 0               CT7 Bandwidth(Kbit/sec): 0
        Actual Bandwidth Information:
        CT0 Bandwidth(Kbit/sec): 20000           CT1 Bandwidth(Kbit/sec): 0
        CT2 Bandwidth(Kbit/sec): 0               CT3 Bandwidth(Kbit/sec): 0
        CT4 Bandwidth(Kbit/sec): 0               CT5 Bandwidth(Kbit/sec): 0
        CT6 Bandwidth(Kbit/sec): 0               CT7 Bandwidth(Kbit/sec): 0
        Explicit Path Name  : -                                Hop Limit: -
        Record Route        : Disabled              Record Label : Disabled
        Route Pinning       : Disabled
        FRR Flag            : Disabled
        IdleTime Remain     : -
        BFD Status          : -
        Soft Preemption     : Enabled 
        Reroute Flag        : Disabled
        Pce Flag            : Normal
Download
Updated: 2018-07-12

Document ID: EDOC1100028530

Views: 102515

Downloads: 336

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next