No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C00 Configuration Guide - MPLS 01

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Checking the Configurations

Checking the Configurations

After configuring MPLS TE manual FRR, you can view detailed information about the bypass tunnel.

Prerequisites

The MPLS TE manual FRR function has been configured.

Procedure

  • Run the display mpls lsp command to check information about the primary tunnel.
  • Run the display mpls te tunnel-interface command to check information about the tunnel interface on the ingress of a primary or bypass tunnel.
  • Run the display mpls te tunnel path command to check information about paths of a primary or bypass tunnel.

Example

Run the following commands to check the previous configurations.

Run the display mpls lsp command to view information about the primary tunnel.

<HUAWEI> display mpls lsp
-------------------------------------------------------------------------------
                 LSP Information: RSVP LSP
-------------------------------------------------------------------------------
  FEC                In/Out Label  In/Out IF                      Vrf Name
  4.4.4.4/32         NULL/11264    -/GE1/0/0

Run the display mpls te tunnel-interface command, and you can see that the tunnel is Up.

<HUAWEI> display mpls te tunnel-interface
    Tunnel Name       : Tunnel1
    Signalled Tunnel Name: -
    Tunnel State Desc : CR-LSP is Up
    Tunnel Attributes   :     
    Active LSP          : Primary LSP                                       
    Traffic Switch      : - 
    Session ID          : 1
    Ingress LSR ID      : 1.1.1.9               Egress LSR ID: 4.4.4.9
    Admin State         : UP                    Oper State   : UP
    Signaling Protocol  : RSVP
    FTid                : 1
    Tie-Breaking Policy : None                  Metric Type  : None
    Bfd Cap             : None                  
    Reopt               : Disabled              Reopt Freq   : -              
    Auto BW             : Disabled              Threshold    : 0 percent
    Current Collected BW: 0 kbps                Auto BW Freq : 0
    Min BW              : 0 kbps                Max BW       : 0 kbps
    Offload             : Disabled              Offload Freq : - 
    Low Value           : -                     High Value   : - 
    Readjust Value      : - 
    Offload Explicit Path Name: 
    Tunnel Group        : -                                              
    Interfaces Protected: -
    Excluded IP Address : -
    Referred LSP Count  : 0  
    Primary Tunnel      : -                     Pri Tunn Sum : -              
    Backup Tunnel       : -                                                    
    Group Status        : -                     Oam Status   : -             
    IPTN InLabel        : -                     Tunnel BFD Status : -                               
    BackUp LSP Type     : None                  BestEffort   : Disabled
    Secondary HopLimit  : -
    BestEffort HopLimit  : -
    Secondary Explicit Path Name: -
    Secondary Affinity Prop/Mask: 0x0/0x0
    BestEffort Affinity Prop/Mask: 0x0/0x0  
    IsConfigLspConstraint: -
    Hot-Standby Revertive Mode:  Revertive
    Hot-Standby Overlap-path:  Disabled
    Hot-Standby Switch State:  CLEAR
    Bit Error Detection:  Disabled
    Bit Error Detection Switch Threshold:  -
    Bit Error Detection Resume Threshold:  -
    Ip-Prefix Name    : -
    P2p-Template Name : -
    PCE Delegate      : Only status report      LSP Control Status : Local control
    Entropy Label       :None 
    Associated Tunnel Group ID: -                 Associated Tunnel Group Type: -
    Auto BW Remain Time : 200 s   Reopt Remain Time  : 100 s

    Primary LSP ID      : 1.1.1.9:19
    LSP State           : UP                    LSP Type     : Primary
    Setup Priority      : 7                     Hold Priority: 7
    IncludeAll          : 0x0
    IncludeAny          : 0x0
    ExcludeAny          : 0x0
    Affinity Prop/Mask  : 0x0/0x0               Resv Style   :  SE
    Configured Bandwidth Information:
    CT0 Bandwidth(Kbit/sec): 20000           CT1 Bandwidth(Kbit/sec): 0
    CT2 Bandwidth(Kbit/sec): 0               CT3 Bandwidth(Kbit/sec): 0
    CT4 Bandwidth(Kbit/sec): 0               CT5 Bandwidth(Kbit/sec): 0
    CT6 Bandwidth(Kbit/sec): 0               CT7 Bandwidth(Kbit/sec): 0
    Actual Bandwidth Information:
    CT0 Bandwidth(Kbit/sec): 20000           CT1 Bandwidth(Kbit/sec): 0
    CT2 Bandwidth(Kbit/sec): 0               CT3 Bandwidth(Kbit/sec): 0
    CT4 Bandwidth(Kbit/sec): 0               CT5 Bandwidth(Kbit/sec): 0
    CT6 Bandwidth(Kbit/sec): 0               CT7 Bandwidth(Kbit/sec): 0
    Explicit Path Name  : -                                Hop Limit: -
    Record Route        : Disabled              Record Label : Disabled
    Route Pinning       : Disabled
    FRR Flag            : Disabled
    IdleTime Remain     : -
    BFD Status          : -
    Soft Preemption     : Enabled 
    Reroute Flag        : Disabled
    Pce Flag            : Normal

Run the display mpls te tunnel path command to view path attributes of tunnels.

<HUAWEI> display mpls te tunnel path
Tunnel Interface Name : Tunnel1
 Lsp ID : 1.1.1.1 :200:1
 Hop Information
  Hop 1   2.1.1.1 Local-Protection available | bandwidth | node
  Hop 2   2.1.1.2  Label 106497
  Hop 3   2.2.2.2
  Hop 4   3.1.1.1 Local-Protection available | bandwidth
  Hop 5   3.1.1.2  Label 3
  Hop 6   3.3.3.3
 Tunnel Interface Name : AutoTunnel67141670
 Lsp ID : 1.1.1.1 :67141670 :2
 Hop Information
  Hop 1   10.1.1.2
  Hop 2   10.1.1.1
  Hop 3   3.3.3.3

 Tunnel Interface Name : AutoTunnel67141671
 Lsp ID : 2.2.2.2 :67141671 :209
 Hop Information
  Hop 1   2.2.2.2
  Hop 2   2.1.1.2
  Hop 3   2.1.1.1
  Hop 4   1.1.1.1
  Hop 5   10.1.1.2
  Hop 6   10.1.1.1
  Hop 7   3.3.3.3
Download
Updated: 2018-07-12

Document ID: EDOC1100028530

Views: 101375

Downloads: 336

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next