Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document.
Note: Even the most advanced machine translation cannot match the quality of professional translators.
Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Checking the Configurations
After configuring CR-LSP backup, you can view information about backup CR-LSPs.
Procedure
- Run the display mpls te tunnel-interface command to check information about a tunnel interface on the ingress of a tunnel.
- Run the display mpls te hot-standby state { all [ verbose ] | interface tunnel-interface-name } command to check information about the hot-standby status.
Example
Run the following commands to check the previous configurations.
Run the display mpls te tunnel-interface command. The command output shows that the tunnel is Up.
<HUAWEI> display mpls te tunnel-interface Tunnel Name : Tunnel1 Signalled Tunnel Name: - Tunnel State Desc : CR-LSP is Up Tunnel Attributes : Active LSP : Primary LSP Traffic Switch : - Session ID : 1 Ingress LSR ID : 1.1.1.9 Egress LSR ID: 4.4.4.9 Admin State : UP Oper State : UP Signaling Protocol : RSVP FTid : 1 Tie-Breaking Policy : None Metric Type : None Bfd Cap : None Reopt : Disabled Reopt Freq : - Auto BW : Disabled Threshold : 0 percent Current Collected BW: 0 kbps Auto BW Freq : 0 Min BW : 0 kbps Max BW : 0 kbps Offload : Disabled Offload Freq : - Low Value : - High Value : - Readjust Value : - Offload Explicit Path Name: Tunnel Group : - Interfaces Protected: - Excluded IP Address : - Referred LSP Count : 0 Primary Tunnel : - Pri Tunn Sum : - Backup Tunnel : - Group Status : - Oam Status : - IPTN InLabel : - Tunnel BFD Status : - BackUp LSP Type : None BestEffort : Disabled Secondary HopLimit : - BestEffort HopLimit : - Secondary Explicit Path Name: - Secondary Affinity Prop/Mask: 0x0/0x0 BestEffort Affinity Prop/Mask: 0x0/0x0 IsConfigLspConstraint: - Hot-Standby Revertive Mode: Revertive Hot-Standby Overlap-path: Disabled Hot-Standby Switch State: CLEAR Bit Error Detection: Disabled Bit Error Detection Switch Threshold: - Bit Error Detection Resume Threshold: - Ip-Prefix Name : - P2p-Template Name : - PCE Delegate : Only status report LSP Control Status : Local control Entropy Label :None Associated Tunnel Group ID: - Associated Tunnel Group Type: - Auto BW Remain Time : 200 s Reopt Remain Time : 100 s Primary LSP ID : 1.1.1.9:19 LSP State : UP LSP Type : Primary Setup Priority : 7 Hold Priority: 7 IncludeAll : 0x0 IncludeAny : 0x0 ExcludeAny : 0x0 Affinity Prop/Mask : 0x0/0x0 Resv Style : SE Configured Bandwidth Information: CT0 Bandwidth(Kbit/sec): 20000 CT1 Bandwidth(Kbit/sec): 0 CT2 Bandwidth(Kbit/sec): 0 CT3 Bandwidth(Kbit/sec): 0 CT4 Bandwidth(Kbit/sec): 0 CT5 Bandwidth(Kbit/sec): 0 CT6 Bandwidth(Kbit/sec): 0 CT7 Bandwidth(Kbit/sec): 0 Actual Bandwidth Information: CT0 Bandwidth(Kbit/sec): 20000 CT1 Bandwidth(Kbit/sec): 0 CT2 Bandwidth(Kbit/sec): 0 CT3 Bandwidth(Kbit/sec): 0 CT4 Bandwidth(Kbit/sec): 0 CT5 Bandwidth(Kbit/sec): 0 CT6 Bandwidth(Kbit/sec): 0 CT7 Bandwidth(Kbit/sec): 0 Explicit Path Name : - Hop Limit: - Record Route : Disabled Record Label : Disabled Route Pinning : Disabled FRR Flag : Disabled IdleTime Remain : - BFD Status : - Soft Preemption : Enabled Reroute Flag : Disabled Pce Flag : Normal
Run the display mpls te hot-standby state interface tunnel interface-name command to view the hot-standby status of the tunnel interface.
<HUAWEI> display mpls te hot-standby state interface Tunnel 1 ---------------------------------------------------------------- Verbose information about the Tunnel1 hot-standby state ---------------------------------------------------------------- Tunnel name : Tunnel1 Session ID : 1 Main LSP index : 0x33 Hot-standby LSP index : 0x161 HSB switch result : hot-standby LSP HSB switch reason : wait to restore WTR config time : 10 s WTR remain time : 2 s Current state : wait to restore Using overlapped path : no
Previous
