No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade
MENU
Support Documentation

NE40E V800R010C00 Configuration Guide - MPLS 01

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring a 1:1 Tunnel Protection Group Consisting of Bidirectional Co-routed CR-LSPs

Example for Configuring a 1:1 Tunnel Protection Group Consisting of Bidirectional Co-routed CR-LSPs

This section provides an example for configuring a 1:1 tunnel protection group consisting of static bidirectional co-routed CR-LSPs. A tunnel protection group provides end-to-end protection for MPLS TE traffic if a network fault occurs.

Networking Requirements

A tunnel protection group consists of static bidirectional co-routed CR-LSPs. If the working tunnel fails, switches traffic to the protection tunnel, which helps improve network reliability.

On the MPLS network shown in Figure 3-33, a working tunnel is established over the path LSRA -> LSRB -> LSRC, and a protection tunnel is established over the path LSRA -> LSRD -> LSRC. To ensure that MPLS TE traffic is not interrupted if a fault occurs, configure static bidirectional co-routed CR-LSPs for both the working and protection tunnels and combine them into a tunnel protection group.

Figure 3-33  Networking diagram for a 1:1 tunnel protection group consisting of static bidirectional co-routed CR-LSPs
NOTE:

Interfaces 1 through 2 in this example are GE 1/0/0, GE 1/0/1, respectively.


Configuration Roadmap

The configuration roadmap is as follows:

  1. Assign an IP address to each interface and configure a routing protocol.

  2. Configure basic MPLS functions and enable MPLS TE.

  3. Set MPLS TE bandwidth attributes for links.

  4. Configure the ingress, transit nodes, and egress for each static bidirectional co-routed CR-LSP.

  5. Configure MPLS TE tunnel interfaces for the working and protection tunnels and bind a specific static bidirectional co-routed CR-LSP to each tunnel interface.

  6. Configure a tunnel protection group.

  7. Configure a detection mechanism to monitor the configured tunnel protection group. MPLS-TP OAM is used in this example.

Data Preparation

To complete the configuration, you need the following data:

  • Tunnel interface's name and IP address, destination address, tunnel ID, and static CR-LSP signaling on LSRA and LSRC

  • Maximum reservable bandwidth and BC bandwidth of each link

  • Next-hop address and outgoing label on the ingress

  • Inbound interface, next-hop address, and outgoing label on the transit node

  • Inbound interface on the egress

Procedure

  1. Assign an IP address to each interface and configure a routing protocol.

    # Assign an IP address and a mask to each interface and configure static routes so that all LSRs can interconnect with each other.

    For configuration details, see Configuration Files in this section.

  2. Configure basic MPLS functions and enable MPLS TE.

    # Configure LSRA.

    [~LSRA] mpls lsr-id 1.1.1.1
[*LSRA] mpls
[*LSRA-mpls] mpls te
[*LSRA-mpls] quit
[*LSRA] interface gigabitethernet 1/0/0
[*LSRA-GigabitEthernet1/0/0] mpls
[*LSRA-GigabitEthernet1/0/0] mpls te
[*LSRA-GigabitEthernet1/0/0] quit
[*LSRA] interface gigabitethernet 1/0/1
[*LSRA-GigabitEthernet1/0/1] mpls
[*LSRA-GigabitEthernet1/0/1] mpls te
[*LSRA-GigabitEthernet1/0/1] commit
[~LSRA-GigabitEthernet1/0/1] quit

    Repeat this step for LSRB, LSRC, and LSRD.

  3. Configure MPLS TE attributes for links.

    # Configure the maximum reservable bandwidth and BC0 bandwidth for the link on the outbound interface of each LSR. The BC0 bandwidth of links must be greater than the tunnel bandwidth (10 Mbit/s).

    # Configure LSRA.

    [~LSRA] interface gigabitethernet 1/0/0
[~LSRA-GigabitEthernet1/0/0] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRA-GigabitEthernet1/0/0] mpls te bandwidth bc0 100000
[*LSRA-GigabitEthernet1/0/0] quit
[*LSRA] interface gigabitethernet 1/0/1
[*LSRA-GigabitEthernet1/0/1] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRA-GigabitEthernet1/0/1] mpls te bandwidth bc0 100000
[*LSRA-GigabitEthernet1/0/1] commit
[~LSRA-GigabitEthernet1/0/1] quit

    # Configure LSRB.

    [~LSRB] interface gigabitethernet 1/0/0
[~LSRB-GigabitEthernet1/0/0] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRB-GigabitEthernet1/0/0] mpls te bandwidth bc0 100000
[*LSRB-GigabitEthernet1/0/0] quit
[*LSRB] interface gigabitethernet 1/0/1
[*LSRB-GigabitEthernet1/0/1] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRB-GigabitEthernet1/0/1] mpls te bandwidth bc0 100000
[*LSRB-GigabitEthernet1/0/1] commit
[~LSRB-GigabitEthernet1/0/1] quit

    # Configure LSRC.

    [~LSRC] interface gigabitethernet 1/0/0
[~LSRC-GigabitEthernet1/0/0] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRC-GigabitEthernet1/0/0] mpls te bandwidth bc0 100000
[*LSRC-GigabitEthernet1/0/0] quit
[*LSRC] interface gigabitethernet 1/0/1
[*LSRC-GigabitEthernet1/0/1] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRC-GigabitEthernet1/0/1] mpls te bandwidth bc0 100000
[*LSRC-GigabitEthernet1/0/1] commit
[~LSRC-GigabitEthernet1/0/1] quit

    # Configure LSRD.

    [~LSRD] interface gigabitethernet 1/0/0
[~LSRD-GigabitEthernet1/0/0] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRD-GigabitEthernet1/0/0] mpls te bandwidth bc0 100000
[*LSRD-GigabitEthernet1/0/0] quit
[*LSRD] interface gigabitethernet 1/0/1
[*LSRD-GigabitEthernet1/0/1] mpls te bandwidth max-reservable-bandwidth 100000
[*LSRD-GigabitEthernet1/0/1] mpls te bandwidth bc0 100000
[*LSRD-GigabitEthernet1/0/1] commit
[~LSRD-GigabitEthernet1/0/1] quit

  4. Configure the ingress, transit nodes, and egress for each static bidirectional co-routed CR-LSP.

    # Configure LSRA as the ingress on both the working and protection static bidirectional co-routed CR-LSPs.
    [~LSRA] bidirectional static-cr-lsp ingress Tunnel 10
[*LSRA-bi-static-ingress-Tunnel10] forward nexthop 2.1.1.2 out-label 20 bandwidth ct0 10000
[*LSRA-bi-static-ingress-Tunnel10] backward in-label 20
[*LSRA-bi-static-ingress-Tunnel10] quit
[*LSRA] bidirectional static-cr-lsp ingress Tunne 20
[*LSRA-bi-static-ingress-Tunnel20] forward nexthop 4.1.1.2 out-label 21 bandwidth ct0 10000
[*LSRA-bi-static-ingress-Tunnel20] backward in-label 21
[*LSRA-bi-static-ingress-Tunnel20] commit
[~LSRA-bi-static-ingress-Tunnel20] quit
    # Configure LSRB as a transit node on the working static bidirectional co-routed CR-LSP.
    [~LSRB]bidirectional static-cr-lsp transit lsp1
[*LSRB-bi-static-transit-lsp1] forward in-label 20 nexthop 3.2.1.2 out-label 40 bandwidth ct0 10000
[*LSRB-bi-static-transit-lsp1] backward in-label 16 nexthop 2.1.1.1 out-label 20 bandwidth ct0 10000
[*LSRB-bi-static-transit-lsp1] commit
[~LSRB-bi-static-transit-lsp1] quit
    # Configure LSRD as a transit node on the protection static bidirectional co-routed CR-LSP.
    [~LSRD]bidirectional static-cr-lsp transit lsp2
[*LSRD-bi-static-transit-lsp2] forward in-label 21 nexthop 3.4.1.2  out-label 41 bandwidth ct0 10000
[*LSRD-bi-static-transit-lsp2] backward in-label 17 nexthop 4.1.1.1 out-label 21 bandwidth ct0 10000
[*LSRD-bi-static-transit-lsp2] commit
[~LSRD-bi-static-transit-lsp2] quit
    # Configure LSRC as the egress on both the working and protection static bidirectional co-routed CR-LSPs.
    [~LSRC] bidirectional static-cr-lsp egress lsp1
[*LSRC-bi-static-egress-lsp1] forward in-label 40 lsrid 1.1.1.1 tunnel-id 100
[*LSRC-bi-static-egress-lsp1] backward nexthop 3.2.1.1 out-label 16 bandwidth ct0 10000
[*LSRC-bi-static-egress-lsp1] quit
[*LSRC] bidirectional static-cr-lsp egress lsp2
[*LSRC-bi-static-egress-lsp2] forward in-label 41 lsrid 1.1.1.1 tunnel-id 101
[*LSRC-bi-static-egress-lsp2] backward nexthop 3.4.1.1 out-label 17 bandwidth ct0 10000
[*LSRC-bi-static-egress-lsp2] commit
[~LSRC-bi-static-egress-lsp2] quit

  5. Configure MPLS TE tunnel interfaces for the working and protection tunnels and bind a specific static bidirectional co-routed CR-LSP to each tunnel interface.

    # On LSRA, configure MPLS TE tunnel interfaces named Tunnel 10 and Tunnel 11.

    [~LSRA] interface Tunnel 10
[*LSRA-Tunnel10] ip address unnumbered interface loopback 1
[*LSRA-Tunnel10] tunnel-protocol mpls te
[*LSRA-Tunnel10] destination 3.3.3.3
[*LSRA-Tunnel10] mpls te tunnel-id 100
[*LSRA-Tunnel10] mpls te signal-protocol cr-static
[*LSRA-Tunnel10] mpls te bidirectional
[*LSRA-Tunnel10]  quit
[*LSRA] interface Tunnel 11
[*LSRA-Tunnel11] ip address unnumbered interface loopback 1
[*LSRA-Tunnel11] tunnel-protocol mpls te
[*LSRA-Tunnel11] destination 3.3.3.3
[*LSRA-Tunnel11] mpls te tunnel-id 101
[*LSRA-Tunnel11] mpls te signal-protocol cr-static
[*LSRA-Tunnel11] mpls te bidirectional
[*LSRA-Tunnel11] commit
[~LSRA-Tunnel11] quit

    # On LSRC, configure MPLS TE tunnel interfaces named Tunnel 20 and Tunnel 21.

    [~LSRC] interface Tunnel 20
[*LSRC-Tunnel20] ip address unnumbered interface loopback 1
[*LSRC-Tunnel20] tunnel-protocol mpls te
[*LSRC-Tunnel20] destination 1.1.1.1
[*LSRC-Tunnel20] mpls te tunnel-id 200
[*LSRC-Tunnel20] mpls te signal-protocol cr-static
[*LSRC-Tunnel20] mpls te passive-tunnel
[*LSRC-Tunnel20] mpls te binding bidirectional static-cr-lsp egress lsp1
[*LSRC-Tunnel20] quit
[*LSRC] interface Tunnel 21
[*LSRC-Tunnel21] ip address unnumbered interface loopback 1
[*LSRC-Tunnel21] tunnel-protocol mpls te
[*LSRC-Tunnel21] destination 1.1.1.1
[*LSRC-Tunnel21] mpls te tunnel-id 201
[*LSRC-Tunnel21] mpls te signal-protocol cr-static
[*LSRC-Tunnel21] mpls te passive-tunnel
[*LSRC-Tunnel21] mpls te binding bidirectional static-cr-lsp egress lsp2
[*LSRC-Tunnel21] commit
[~LSRC-Tunnel21] quit

  6. Configure a tunnel protection group.

    # On LSRA, configure a tunnel protection group that consists of a working tunnel named Tunnel 10 and its protection tunnel named Tunnel 11.
    [~LSRA] interface Tunnel 10
[~LSRA-Tunnel10] mpls te protection tunnel 101 mode revertive wtr 0
[*LSRA-Tunnel10] commit
[~LSRA-Tunnel10] quit

    # On LSRC, configure a tunnel protection group that consists of a working tunnel named Tunnel 20 and its protection tunnel named Tunnel 21.

    [~LSRC] interface Tunnel 20
[~LSRC-Tunnel20] mpls te protection tunnel 201 mode revertive wtr 0
[*LSRC-Tunnel20] commit
[~LSRC-Tunnel20] quit

  7. Configure a detection mechanism to monitor the configured tunnel protection group. MPLS-TP OAM is used in this example.

    On LSRA, configure MPLS-TP OAM on Tunnel10:
    [~LSRA] mpls-tp meg abc
[~LSRA-Tunnel10] me te interface Tunnel 10 mep-id 1 remote-mep-id 2
[*LSRA-Tunnel10] commit
[~LSRA-Tunnel10] quit
    On LSRC, configure MPLS-TP OAM on Tunnel20:
    [~LSRC] mpls-tp meg abc
[~LSRC-Tunnel20] me te interface Tunnel 20 mep-id 1 remote-mep-id 2
[*LSRC-Tunnel20] commit
[~LSRC-Tunnel20] quit

  8. Verify the configuration.

    After completing the configuration, run the display mpls te protection tunnel all verbose command on LSRA. The command output shows that the tunnel interfaces are working properly.

    [~LSRA] display mpls te protection tunnel all verbose

----------------------------------------------------------------
Verbose information about the No."1" protection-group
----------------------------------------------------------------
Work-tunnel id                           : 100
Protect-tunnel id                        : 101
Work-tunnel name                         : Tunnel10
Protect-tunnel name                      : Tunnel11
Work-tunnel reverse-lsp                  : -
Protect-tunnel reverse-lsp               : -
Bridge type                              : 1:1      
Switch type                              : bidirectional
Switch result                            : work-tunnel
Tunnel using Best-Effort                 : none
Tunnel using Ordinary                    : none
Work-tunnel frr in use                   : none
Work-tunnel defect state                 : non-defect
Protect-tunnel defect state              : non-defect
Work-tunnel forward-lsp defect state     : non-defect
Protect-tunnel forward-lsp defect state  : non-defect
Work-tunnel reverse-lsp defect state     : non-defect
Protect-tunnel reverse-lsp defect state  : non-defect
HoldOff config time                      : 0ms
HoldOff remain time                      : -
WTR config time                          : 0s
WTR remain time                          : -
Mode                                     : revertive
Using same path                          : -
Local state                              : no request
Far end request                          : no request

Configuration Files

  • LSRA configuration file

    #
sysname LSRA
#
mpls lsr-id 1.1.1.1
#
mpls
 mpls te
#
bidirectional static-cr-lsp ingress Tunnel10
 forward nexthop 2.1.1.2 out-label 20 bandwidth ct0 10000
 backward in-label 20
#
bidirectional static-cr-lsp ingress Tunnel11
 forward nexthop 4.1.1.2 out-label 21 bandwidth ct0 1000
 backward in-label 21
#
interface GigabitEthernet1/0/0
 undo shutdown
 ip address 2.1.1.1 255.255.255.0
 mpls
 mpls te
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
#
interface GigabitEthernet1/0/1
 undo shutdown
 ip address 4.1.1.1 255.255.255.0
 mpls
 mpls te
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
#
interface LoopBack1
 ip address 1.1.1.1 255.255.255.255
#
interface Tunnel10
 ip address unnumbered interface LoopBack1
 tunnel-protocol mpls te
 destination 3.3.3.3
 mpls te signal-protocol cr-static
 mpls te tunnel-id 100
 mpls te bidirectional
 mpls te protection tunnel 101 mode revertive wtr 0
#
interface Tunnel11
 ip address unnumbered interface LoopBack1
 tunnel-protocol mpls te
 destination 3.3.3.3
 mpls te signal-protocol cr-static
 mpls te tunnel-id 101
 mpls te bidirectional
#
ip route-static 2.2.2.2 255.255.255.255 2.1.1.2
ip route-static 3.3.3.3 255.255.255.255 2.1.1.2
ip route-static 3.3.3.3 255.255.255.255 4.1.1.2
ip route-static 4.4.4.4 255.255.255.255 4.1.1.2
#
mpls-tp meg Tunnel10
 me te interface Tunnel10 mep-id 1 remote-mep-id 2 
#
return

  • LSRB configuration file

    #
sysname LSRB
#
mpls lsr-id 2.2.2.2
#
mpls
 mpls te
#
bidirectional static-cr-lsp transit lsp1
 forward in-label 20 nexthop 3.2.1.2 out-label 40 bandwidth ct0 10000
 backward in-label 16 nexthop 2.1.1.1 out-label 20 bandwidth ct0 10000
#
interface GigabitEthernet1/0/0
 undo shutdown
 ip address 2.1.1.2 255.255.255.0
 mpls
 mpls te
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
#
interface GigabitEthernet2/0/0
 undo shutdown
 ip address 3.2.1.1 255.255.255.0
 mpls
 mpls te
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
#
interface LoopBack1
 ip address 2.2.2.2 255.255.255.255
#
ip route-static 1.1.1.1 255.255.255.255 2.1.1.1
ip route-static 3.3.3.3 255.255.255.255 3.2.1.2
#
return

  • LSRC configuration file

    #
sysname LSRC
#
mpls lsr-id 3.3.3.3
#
mpls
 mpls te
#
bidirectional static-cr-lsp egress lsp1
 forward in-label 40 lsrid 1.1.1.1 tunnel-id 100
 backward nexthop 3.2.1.1 out-label 16 bandwidth ct0 10000
#
bidirectional static-cr-lsp egress lsp2
 forward in-label 41 lsrid 1.1.1.1 tunnel-id 101
 backward nexthop 3.4.1.1 out-label 17 bandwidth ct0 10000
#
interface GigabitEthernet1/0/0
 undo shutdown
 ip address 3.2.1.2 255.255.255.0
 mpls
 mpls te
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
#
interface GigabitEthernet1/0/1
 undo shutdown  
 ip address 3.4.1.2 255.255.255.0
 mpls           
 mpls te        
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
# 
interface LoopBack1
 ip address 3.3.3.3 255.255.255.255
#
interface Tunnel20
 ip address unnumbered interface LoopBack1
 tunnel-protocol mpls te
 destination 1.1.1.1
 mpls te signal-protocol cr-static
 mpls te tunnel-id 200
 mpls te passive-tunnel
 mpls te binding bidirectional static-cr-lsp egress lsp1
 mpls te protection tunnel 201 mode revertive wtr 0
#
interface Tunnel21
 ip address unnumbered interface LoopBack1
 tunnel-protocol mpls te
 destination 1.1.1.1
 mpls te signal-protocol cr-static
 mpls te tunnel-id 201
 mpls te passive-tunnel
 mpls te binding bidirectional static-cr-lsp egress lsp2
#               
ip route-static 1.1.1.1 255.255.255.255 3.2.1.1
ip route-static 1.1.1.1 255.255.255.255 3.4.1.1
ip route-static 2.2.2.2 255.255.255.255 3.2.1.1
ip route-static 4.4.4.4 255.255.255.255 3.4.1.1
#
mpls-tp meg Tunnel10
 me te interface Tunnel20 mep-id 1 remote-mep-id 2
#
return

  • LSRD configuration file

    #
sysname LSRD
#
mpls lsr-id 4.4.4.4
#
mpls
 mpls te
#
bidirectional static-cr-lsp transit lsp2
 forward in-label 21 nexthop 3.4.1.2 out-label 41 bandwidth ct0 10000
 backward in-label 17 nexthop 4.1.1.1 out-label 21 bandwidth ct0 10000
##
interface GigabitEthernet1/0/0
 undo shutdown
 ip address 2.1.1.2 255.255.255.0
 mpls
 mpls te
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
#
interface GigabitEthernet1/0/0
 undo shutdown  
 ip address 4.1.1.2 255.255.255.0
 mpls           
 mpls te        
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
#
interface GigabitEthernet1/0/1
 undo shutdown  
 ip address 3.4.1.1 255.255.255.0
 mpls           
 mpls te        
 mpls te bandwidth max-reservable-bandwidth 100000
 mpls te bandwidth bc0 100000
# 
interface LoopBack1
 ip address 4.4.4.4 255.255.255.255
#               
ip route-static 1.1.1.1 255.255.255.255 4.1.1.1
ip route-static 3.3.3.3 255.255.255.255 3.4.1.2
#
return
Download
Updated: 2018-07-12

Document ID: EDOC1100028530

Views: 101979

Downloads: 336

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next
Enterprise APP

Copyright © 2019 Huawei Technologies Co., Ltd. All rights reserved.