No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C00 Configuration Guide - MPLS 01

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Setting BFD Parameters on the Ingress

Setting BFD Parameters on the Ingress

BFD parameters must be configured on the ingress before a BFD session is established to monitor an LDP LSP.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    bfd session-name bind ldp-lsp peer-ip ip-address nexthop ip-address [ interface interface-type interface-number ]

    A BFD session is bound to a dynamic LSP.

  3. Run:

    discriminator local discr-value

    The local discriminator of the BFD session is set.

  4. Run:

    discriminator remote discr-value

    The remote discriminator of the BFD session is set.

    NOTE:

    The local discriminator of a local device and the remote discriminator of a remote device must be the same, and the remote discriminator of the local device and the local discriminator of the remote device must be the same. A discriminator inconsistency causes BFD session establishment failures.

  5. Run:

    process-pst

    A BFD session is allowed to modify the PST.

    If the BFD session on a trunk or VLAN member interface allows BFD to modify the PST, and a BFD session is configured on the main interface, you must configure the wait to restore (WTR) time for the BFD session that monitors the main interface. This prevents the BFD session on the main interface from flapping when the member interface joins or leaves the main interface.

  6. (Optional) Run:

    min-tx-interval interval

    The local minimum interval at which BFD packets are sent is set.

    When the reverse tunnel is an IP link, the local parameters cannot be configured.

    Effective local interval at which BFD packets are sent = MAX { Locally configured minimum interval at which BFD packets are sent, Remotely configured minimum interval at which BFD packets are received }

    Effective local interval at which BFD packets are received = MAX { Remotely configured interval at which BFD packets are sent, Locally configured interval at which BFD packets are received }

    Local detection interval = Local interval at which BFD packets are received x Remote BFD detection multiplier

    For example, the locally configured interval at which BFD packets are sent is 200 ms, the interval at which BFD packets are received is 300 ms, and the detection multiplier is 4. The remotely configured interval at which BFD packets are sent is 100 ms, the interval at which BFD packets are received is 600 ms, and the detection multiplier is 5.

    • The effective local interval at which BFD packets are sent is 600 ms (MAX { 200 ms, 600 ms }), the effective local interval at which BFD packets are received is 300 ms (MAX { 100 ms, 300 ms }), and the detection interval is 1500 ms (300 ms x 5).

    • The effective remote interval at which BFD packets are sent is 300 ms (MAX { 100 ms, 300 ms }), the effective remote interval at which BFD packets are received is 600 ms (MAX { 200 ms, 600 ms}), and the detection interval is 2400 ms (600 ms x 4).

    NOTE:

    When POS-Trunk interfaces work in 1:1 mode, the local actual receiving interval must be greater than or equal to three times of the POS-Trunk switchover time. Otherwise, the BFD session may go Down during the POS-Trunk switchover.

  7. (Optional) Run:

    min-rx-interval interval

    The local minimum interval for receiving BFD packets is set.

    When the reverse tunnel is an IP link, the local parameters cannot be configured.

  8. (Optional) Run:

    detect-multiplier multiplier

    The local BFD detection multiplier is set.

  9. Run:

    commit

    The configurations are committed.

Download
Updated: 2018-07-12

Document ID: EDOC1100028530

Views: 102503

Downloads: 336

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next