No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionServer G5500 Server G560 V5 Compute Node Maintenance and Service Guide 03

Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Front Panel Indicators and Buttons

Front Panel Indicators and Buttons

Front Panel Indicators and Buttons of the G560 V5

Figure 8-5 Front panel indicators and buttons of the G560 V5

1

Power button/indicator

2

UID button/indicator

3

HLY indicator

4

2.5-inch SAS/SATA drive activity indicator

5

2.5-inch SAS/SATA drive fault indicator

6

2.5-inch SAS/SATA/NVMe drive fault indicator

7

2.5-inch SAS/SATA/NVMe drive activity indicator

8

M.2 FRU activity indicator

9

M.2 FRU fault indicator

-

-

Front Panel Indicators of the GP608

Figure 8-6 Front panel indicators of the GP608

1

3.5-inch SAS/SATA drive activity indicator

2

3.5-inch SAS/SATA drive fault indicator

Front Panel Indicators of the GS608

Figure 8-7 Front panel indicators of the GS608

1

2.5-inch SAS/SATA drive activity indicator

2

2.5-inch SAS/SATA drive fault indicator

Table 8-1 describes the front panel indicators and buttons.

Table 8-1 Front panel indicator and button description

Silkscreen

Indicator/Button

State Description

Power button/indicator

  • Off: The compute node is not connected to a power source.
  • Blinking yellow: The power button is locked.
  • The power button is locked when the iBMC is being started during the compute node startup.
  • Steady yellow: The compute node is ready to be powered on.
  • Steady green: The compute node is properly powered on.
NOTE:
  • When the compute node is powered on, pressing the power button for less than 1 second will power it off.
  • When the compute node is powered on, holding down this button for 6 seconds will force the node to power off.
  • When the compute node is ready to be powered on, pressing this button for less than 1 second will start the node.

UID

UID button/indicator

The UID indicator is used to locate the compute node in a chassis. You can turn on or off the UID indicator by pressing the UID button or using the iBMC.

  • Off: The compute node is powered off or not being located.
  • Steady blue: The compute node is located.
  • Blinking blue: The compute node is located and differentiated from other located compute nodes.
NOTE:
  • You can press this button for less than 1 second to turn on or off the UID indicator.
  • You can hold down the UID button for 4 to 6 seconds to reset the iBMC.

HLY

Health indicator

  • Off: The compute node is not powered on.
  • Steady green: The compute node hardware is operating properly.
  • Blinking red (at 1 Hz): A major alarm has been generated for the compute node.
  • Blinking red (at 5 Hz): A critical alarm has been generated for the compute node, or the compute node is not securely installed.

Drive or M.2 FRU activity indicator

  • Off: The drive is faulty or not detected.
  • Blinking green: Data is being read from or written to the drive, or synchronized between drives.
  • Steady green: The drive is not being accessed.

Drive or M.2 FRU fault indicator

  • Off: The drive is operating properly.
  • Blinking yellow: The drive is being located, or RAID is being rebuilt.
  • Steady yellow: The drive is faulty or not detected.

NVMe SSD activity indicator

  • Off: The SSD is faulty or not detected.
  • Blinking green: Data is being read from or written to the SSD, or synchronized between SSDs.
  • Steady green: The SSD is not being accessed.

NVMe SSD fault indicator

  • Off: The SSD is operating properly.
  • Blinking yellow (at 0.5 Hz): The SSD completes the hot swap process and is ready to be removed.
  • Blinking yellow (at 2 Hz): The SSD is being located or hot-swapped.
  • Steady yellow: The SSD is faulty or not detected.
Translation
Download
Updated: 2018-12-14

Document ID: EDOC1100031432

Views: 23661

Downloads: 39

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next