No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

XH321L V5 Server Node V100R005 Maintenance and Service Guide 02

Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Logging In to the iBMC CLI or WebUI Through the iBMC Management Network Port

Logging In to the iBMC CLI or WebUI Through the iBMC Management Network Port

Data

  • IP address of the iBMC management network port on the server node
  • User name and password of the server node iBMC
Table 10-2 Default data for server nodes

Server Node

Default User

Default Password

Default IP Address

Default Subnet Mask

XH321L V5

Administrator

Admin@9000

  • Slot 1: 10.10.1.101
  • Slot 2: 10.10.1.102
  • Slot 3: 10.10.1.103
  • Slot 4: 10.10.1.104

255.255.255.0

Software

PuTTY.exe (third-party software)

Procedure

If you want to log in to the iBMC CLI or WebUI through the iBMC management network port, the management network port mode must be the fixed or automatic mode.

  1. Connect a PC to the iBMC management network port of a server node.

    Connect a PC to the iBMC management network port of a server node using a network cable. See Figure 10-18.
    Figure 10-18 Connecting a cable to the management network port of a server node

  2. Set the IP address of the PC.

    Set the IP address, subnet mask, or route of the PC and ensure that the PC can communicate with the iBMC management network port.

    Run the Ping iBMC management network port IP address command on the PC CLI to check whether the PC can properly communicate with the server.

  3. (Optional) Log in to the iBMC WebUI of the server node.

    1. Open a browser, enter the IP address of the iBMC management network port in the address box, and press Enter.
    2. On the login page shown in Figure 10-19, enter the user name and password, and click Log In.
      Figure 10-19 Logging in to the iBMC
      NOTE:

      Change the default password when logging in to the iBMC for the first time.

  4. (Optional) Log in to the iBMC CLI of the server node.

    1. On the PC, double-click PuTTY.exe.

      The PuTTY Configuration window is displayed, as shown in Figure 10-20.

      Figure 10-20 PuTTY Configuration
    2. Set the login parameters.

      The parameters are described as follows:

      • Host Name (or IP address): Enter the server node IP address, for example, 10.10.1.104.
      • Port: Enter 22.
      • Connection type: Set it to SSH.
      NOTE:

      Configure Host Name (or IP address) and Saved Sessions, and click Save. You can double-click the saved record under Saved Sessions to log in to the server the next time.

    3. Click Open.

      The PuTTY window is displayed.

      NOTE:
      • If this is your first login to the server, the PuTTY Security Alert dialog box is displayed. Click Yes to proceed.
      • If the account entered during server login is incorrect, reconnect PuTTY.
    4. Enter the user name and password.

      After login, the host name of the device is displayed on the left of the prompt.

Download
Updated: 2019-01-08

Document ID: EDOC1100033003

Views: 7830

Downloads: 12

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next