No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OSN 9800 V100 Configuration Guide 03

This document introduces service configuration process for OSN 9800.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuration Example of a UNI-UNI CES (VC4 Level) Service

Configuration Example of a UNI-UNI CES (VC4 Level) Service

This topic describes the configuration example of a UNI-UNI CES service at the VC4 level.

Example Description

This topic describes the application scenario of the UNI-UNI CES services.

Figure 4-13 shows the networking diagram of the UNI-UNI CES services. OTN devices can be used between the RNC and NodeB to receive and transmit CES services. The service requirements are as follows:
  • NE1 is OSN 9800 U32 Standard.
  • The EC116 board is used between NodeBs and the RNC to receive and transmit VC4 CES services.
Figure 4-13 Networking of the CES service

Service Planning

If CES services need to be transmitted between each NodeB and RNC, a UNI-UNI CES service must be created first.

Use the UNI-UNI mode to receive and transmit local services and configure one UNI-UNI CES service between each NodeB and RNC.

Table 4-21 lists the configuration parameters of NE1.

Table 4-21 Configuration parameters of the CES service

Attribute

Value

Service ID

1

Service Type

UNI-UNI

PW Type

CEP

Service Name

CES1

Service type of CES

Common

AC Configuration List 1

Port

VC4 0/12/0/15:1

AC Configuration List 2

Port

VC4 0/12/0/16:1

Configuring CES Services on a Per-NE Basis

This topic describes how to configure a CES service at the VC4 level in the example on a per-NE basis.

Prerequisites

You must be an NM user with "NE operator" authority or higher.

You must understand the networking, requirements and service planning of the example.

A network must be created.

Procedure

  1. Configure the channel mode.
    1. In the NE Explorer, right-click NE1 and choose the EC116 board. Then, choose Configuration > Interface Management > Channel Configuration from the navigation tree.
    2. Set Multiplex mode of port 15 on the NodeB side to VC4.

      Refer to steps 1.a through 1.b to configure port 16 on the RNC side.

  2. Create local CES service CES1.
    1. In the NE Explorer, right-click NE1 and choose Configuration > CES Service Management from the navigation tree.
    2. Click Create, and set PW type to CEP. Set parameters for CES1.
    3. Click Port. In the dialog box that is displayed, choose a VC4 interface and set Link protocol to TDM link protocol. Click Apply and click OK.



      Item

      Value

      Service ID

      1

      Service type

      NUI-NNI

      PW type

      CEP

      Service name

      CES1

      AC configuration list 1

      Port

      VC4 0/12/0/15:1

      NOTE:

      The interface format is as follows: VC4 0/slot ID/subrack name/port number:VC4 higher-order channel number. For example, VC4 0/12/0/15:1 indicates that a VC4 higher-order channel on interface 15 of a board in slot 12 in subrack 0 is set as an AC-side interface.

      AC configuration list 2

      Port

      VC4 0/12/0/16:1

    4. Click OK, and the Operation Result dialog box is displayed, indicating that the operation is successful. Click Close.
Translation
Download
Updated: 2019-09-05

Document ID: EDOC1100033663

Views: 18976

Downloads: 667

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next